The surface passivation of a CMOS image sensor (CIS) is highly beneficial for the overall improvement of a device performance. We employed the thermal atomic layer deposition (T-ALD) and plasma enhanced (PE-ALD) techniques for the deposition of 20 nm HfO 2 as well as stacked with 3 and 5 nm Al 2 O 3 thin films. The HfO 2 /Si and Al 2 O 3 /HfO 2 /Si metal-oxide-semiconductor structures were used to analyze the fixed charge density ( $\text{Q}_{\mathrm {f}}$ ) and interface trap density ( $\text{D}_{\mathrm {it}}$ ). The as-synthesized samples show high $\text{D}_{\mathrm {it}}$ and $\text{Q}_{\mathrm {f}}$ values (10 12 cm −2 eV −1 ) and a minority carrier lifetime of 15–300 $\mu \text{s}$ . The finite-difference time-domain simulation of high-k dielectrics confirmed that the Al 2 O 3 (top)/HfO 2 stacked structures expected higher quantum efficiency for CIS application. The effect of vacuum annealing (VA) and forming gas annealing (FGA) treatments succeeded with the decomposition of the $\text{D}_{\mathrm {it}}$ and increase in carrier lifetime. The H 2 ambient FGA samples showed a remarkable decrease in the $\text{D}_{\mathrm {it}}$ values. To improve the overall performance of the device after passivation, we employed an Al 2 O 3 /HfO 2 bilayer structure, which showed a low $\text{D}_{\mathrm {it}}$ of 10 11 cm −2 eV −1 and a minority carrier lifetime of $\sim 3$ ,700 $\mu \text{s}$ after 400 °C and 30 min FGA. We believe that this surface passivation strategy will pave way for future CIS technology regarding the development of lower defective surface and superior performance.
Herein, the fabrication of a novel highly sensitive and fast hydrogen (H2) gas sensor, based on the Ta2O5 Schottky diode, is described. First, Ta2O5 thin films are deposited on silicon carbide (SiC) and silicon (Si) substrates via a radio frequency (RF) sputtering method. Then, Pd and Ni are respectively deposited on the front and back of the device. The deposited Pd serves as a H2 catalyst, while the Ni functions as an Ohmic contact. The devices are then tested under various concentrations of H2 gas at operating temperatures of 300, 500, and 700 °C. The results indicate that the Pd/Ta2O5 Schottky diode on the SiC substrate exhibits larger concentration and temperature sensitivities than those of the device based on the Si substrate. In addition, the optimum operating temperature of the Pd/Ta2O5 Schottky diode for use in H2 sensing is shown to be about 300 °C. At this optimum temperature, the dynamic responses of the sensors towards various concentrations of H2 gas are then examined under a constant bias current of 1 mA. The results indicate a fast rise time of 7.1 s, and a decay of 18 s, for the sensor based on the SiC substrate.
Photosensitive polyimides (PSPIs) have been widely developed in microelectronics, which is due to their excellent thermal properties and reasonable dielectric properties and can be directly patterned to simplify the processing steps. In this study, 3 μm~7 μm thick PSPI films were deposited on different substrates, including Si, 50 nm SiN, 50 nm SiO2, 100 nm Cu, and 100 nm Al, for the optimization of the process of integration with Cu films. In situ temperature-dependent resistance measurements were conducted by using a four-point probe system to study the changes in resistance of the 70 nm thick Cu films on different dielectrics with thick diffusion films of 30 nm Mn, Co, and W films in a N2 ambient. The lowest possible change in thickness due to annealing at the higher temperature ranges of 325 °C to 375 °C is displayed, which suggests the high stability of PSPI. The PSPI films show good adhesion with each Cu diffusion barrier up to 350 °C, and we believe that this will be helpful for new packaging applications, such as a 3D IC with a Cu interconnect.
SiC-based avalanche photodiodes (APDs) are the preferred devices for use in high-sensitivity UV detectors. However, the defect densities on the surface or in the bulk of the SiC epitaxial layer limit the performance of APDs. In this study, the effect of defects resulting in electrical fatigue in 4H-SiC APDs on device performance was analyzed. Further, fast and efficient defect analysis and detection methods based on laser scanning confocal microscopy are proposed for high-performance APD fabrication. Experimental results show a correlation between the electrical transport and optical properties with respect to the defect behavior in the active and non-active area based on the physical morphology.
24 June 2019 in Japanese Journal of Applied Physics
We investigate the Ni–Si film silicidation process on 4H-SiC and Si substrates and compare the thermal stability of the films grown on each substrate. The Ni–Si films were subjected to rapid thermal annealing (RTA) in the temperature range 575 °C–975 °C for 90 s, and their thermal stability was characterized by in-situ temperature-dependent sheet resistance measurements at temperatures of 25 °C–550 °C. The sheet resistance of a 40 nm thick Ni film was observed to increase sharply above 330 °C in the Ni/Si (100) interface, but slightly decrease at approximately 480 °C in the Ni/4H-SiC interface. The thermal stability of the films was found to be significantly dependent on the RTA temperature. Thermally stable Ni–Si silicide films with excellent Ohmic properties (no hysteresis behavior) can be obtained on 4H-SiC substrates at RTA temperatures of 925 °C–975 °C and can used for application in MOSFET devices.