Hengyong Bu

Dr. Hengyong Bu


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 October 2021 in Materials
Verified
Journal Article
Open access
PDF file
HYHongbin Yang
Hongbin Yang
HBHengyong Bu
Hengyong Bu
MLMengnie Victor Li
Mengnie Victor Li
XLXin Lu
Xin Lu
Hot compression experiments of annealed 7075 Al alloy were performed on TA DIL805D at different temperatures (733, 693, 653, 613 and 573 K) with different strain rates (1.0, 0.1, 0.01 and 0.001 s−1.) Based on experimental data, the strain-compensated Arrhenius model (SCAM) and the back-propagation artificial neural network model (BP-ANN) were constructed for the prediction of the flow stress. The predictive power of the two models was estimated by residual analysis, correlation coefficient (R) and average absolute relative error (AARE). The results reveal that the deformation parameters including strain, strain rate, and temperature have a significant effect on the flow stress of the alloy. Compared with the SCAM model, the flow stress predicted by the BP-ANN model is in better agreement with experimental values. For the BP-ANN model, the maximum residual is only 1 MPa, while it is as high as 8 MPa for the SCAM model. The R and AARE for the SCAM model are 0.9967 and 3.26%, while their values for the BP-ANN model are 0.99998 and 0.18%, respectively. All these reflect that the BP-ANN model has more accurate prediction ability than the SCAM model, which can be applied to predict the flow stress of the alloy under high temperature deformation.

28 October 2023 in Metals
Verified
Journal Article
Open access
PDF file
QQQingwen Qi
Qingwen Qi
福李福建话 李
福建话 李
Yonghua DuanYonghua Duan
Yonghua Duan
HBHengyong Bu
Hengyong Bu
MLMengnie Victor Li
Mengnie Victor Li
Today, 7xxx aluminum alloys are widely used in aerospace and other fields due to their excellent properties such as low density, high specific strength, and good processing performance. The heat treatment process of 7xxx aluminum alloy is crucial in controlling the strengthening phases and grain size, which is a significant way to enhance the alloy’s performance. In this study, solution heat treatment tests of 7050 aluminum alloys were carried out at different temperatures, ranging from 440 °C to 470 °C, with a holding time ranging from 0.5 h to 8 h, using a DIL 805A thermomechanical test machine. The microstructural evolution during the solution heat treatment was characterized using an optical microscope (OM), a scanning electron microscope (SEM), and a transmission electron microscope (TEM). The effects of the solution parameters on the alloy’s microhardness were analyzed using a digital Vickers microhardness tester. According to the ASTM E112-13 standard, The Anelli grain growth models were established to illustrate the grain size evolution during solution heat treatment, and a modified Anelli grain growth model was established. The results indicated that the grain size significantly increases with the increase in the solution heat treatment time and temperature. The Anelli grain growth model can illustrate the phenomenon of grain growth more accurately in the solution heat treatment process of 7050 aluminum alloy. It was found that prolonging the time and elevating the temperature of the solution heat treatment reduced the microhardness of the aluminum alloy because of the dissolution of the precipitates.

28 July 2022 in Metals
Verified
Journal Article
Open access
PDF file
HBHengyong Bu
Hengyong Bu
QLQin Li
Qin Li
SLShaohong Li
Shaohong Li
MLMengnie Victor Li
Mengnie Victor Li
Isothermal compression behaviors of 5CrNiMoV steel were studied at temperatures of 870, 800, 750, and 700 °C, with strain rates of 0.001, 0.005, 0.01, 0.05, and 0.1 s−1, the compression temperatures 870 and 800 °C are above Ac3, as well as 750 and 700 °C below Ac3 temperature. The Modified Johnson–Cook (MJC) model and the Strain–Compensated Arrhenius (SCA) model were employed to demonstrate the relationship between the flow stress and the compression parameters. The correlation coefficient (R) and average absolute relative error (AARE) between the calculational and experimental flow stress were used to evaluate the accuracy of the two models. The results show that the effect of dynamic softening on flow stress is much more significant at higher temperatures and lower strain rates, while this effect is not obvious when the strain rate exceeds 0.005 s−1 with the temperature below Ac3. The MJC model has a good accuracy close to the reference conditions (0.001 s−1 and 700 °C), and it is suitable to predict the plastic behavior when the flow stress is lower than 200 Mpa. The unbiased AARE values were 6.82 and 5.71 for MJC model and SCA model, respectively, which implied the SCA model has a higher accuracy than the MJC model. The SCA model was believed to be capable of being used to illustrate the thermomechanical behavior of 5CrNiMoV tool steel in a wide range of plastic deformation conditions.

10 April 2024 in Materials & Design
Verified
Journal Article
Open access
YZYun Zeng
Yun Zeng
HBHengyong Bu
Hengyong Bu
PLPeikai Li
Peikai Li
CWChao Wang
Chao Wang
SLShaohong Li
Shaohong Li

17 April 2025 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
SFShanming Fan
Shanming Fan
QYQing Yu
Qing Yu
MPMingjun Peng
Mingjun Peng
HBHengyong Bu
Hengyong Bu
XZXiaolong Zhou
Xiaolong Zhou
MLMengnie Li
Mengnie Li

18 November 2022 in Metals
Verified
Journal Article
Open access
PDF file
HBHengyong Bu
Hengyong Bu
LCLu Chen
Lu Chen
Yonghua DuanYonghua Duan
Yonghua Duan
Thermal-induced porosity (TIP) is one of the major defects in powder metallurgy (P/M) superalloys, and it seriously affects the performance of P/M superalloys. The effects of solution heat treatment on the growth of the TIP of the nickel-based P/M superalloy FGH97 were investigated. A series of solution heat treatment tests were carried out at holding temperatures ranging from 1150 to 1200 °C, with holding times ranging from 0.5 to 8 h. The results showed that the holding time, temperature, and the initial volume of porosity are the primary factors influencing porosity growth, and the volume fraction of TIPs increases by increasing the temperature or extending the holding time. The porosity growth models were constructed based on the porosity statistics combined with a nonlinear fitting method. To evaluate the accuracy of the proposed models, the correlation coefficient (R) and average absolute relative error (AARE) were calculated between the predicted and experimental values. The unbiased AARE values were 2.06% and 3.99% for the average value of TIP and the worst value of TIP, respectively, which imply that the proposed porosity growth models have greater accuracy and can be used to illustrate TIP behavior in solution heat treatment.