Wei Hua Ho

Dr. Wei Hua Ho

orcid

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2018 in Separation and Purification Technology
Verified
Journal Article
Closed access
UAUyiosa Osagie Aigbe
Uyiosa Osagie Aigbe
RDRaghunath Das
Raghunath Das
WHWei Hua Ho
Wei Hua Ho
VSVallabhapurapu Srinivasu
Vallabhapurapu Srinivasu
AMArjun Maity
Arjun Maity

9 December 2019 in Cardiovascular Engineering and Technology
Verified
Journal Article
Open access
PDF file
WHWei Hua Ho
Wei Hua Ho
ITI. J. Tshimanga
I. J. Tshimanga
MNMalebogo Ngoepe
Malebogo Ngoepe
MJMark C Jermy
Mark C Jermy
PGPatrick Henry Geoghegan
Patrick Henry Geoghegan
Purpose: Fabrication of a suitable flow model or phantom is critical to the study of biomedical fluid dynamics using optical flow visualization and measurement methods. The main difficulties arise from the optical properties of the model material, accuracy of the geometry and ease of fabrication. Methods: Conventionally an investment casting method has been used, but recently advancements in additive manufacturing techniques such as 3D printing have allowed the flow model to be printed directly with minimal post-processing steps. This study presents results of an investigation into the feasibility of fabrication of such models suitable for particle image velocimetry (PIV) using a common 3D printing Stereolithography process and photopolymer resin. Results: An idealised geometry of a cerebral aneurysm was printed to demonstrate its applicability for PIV experimentation. The material was shown to have a refractive index of 1.51, which can be refractive matched with a mixture of de-ionised water with ammonium thiocyanate (NH4SCN). The images were of a quality that after applying common PIV pre-processing techniques and a PIV cross-correlation algorithm, the results produced were consistent within the aneurysm when compared to previous studies. Conclusions: This study presents an alternative low-cost option for 3D printing of a flow phantom suitable for flow visualization simulations. The use of 3D printed flow phantoms reduces the complexity, time and effort required compared to conventional investment casting methods by removing the necessity of a multi-part process required with investment casting techniques.

1 June 2017 in International Journal of Heat and Fluid Flow
Verified
Journal Article
Closed access
TFT.J. Flint
T.J. Flint
MJM.C. Jermy
M.C. Jermy
Tze How NewTze How New
Tze How New
WHWei Hua Ho
Wei Hua Ho

1 November 2018 in Desalination and Water Treatment
Verified
Journal Article
Open access
UAUyiosa Osagie Aigbe
Uyiosa Osagie Aigbe
MKMohammed Khenfouch
Mohammed Khenfouch
WHWei Hua Ho
Wei Hua Ho
AMArjun Maity
Arjun Maity
VVVijaya Srinivasu Vallabhapurapu
Vijaya Srinivasu Vallabhapurapu
NHNanjundaswamy Marishetty Hemmaragala
Nanjundaswamy Marishetty Hemmaragala

2 January 2021 in AIChE Journal
Verified
Journal Article
Closed access
PDF file
JSJianqi Shen
Jianqi Shen
YLYun‐Chao Li
Yun‐Chao Li
WHWei Hua Ho
Wei Hua Ho
XLXinying Liu
Xinying Liu
DHDiane Hildebrandt
Diane Hildebrandt

1 March 2008 in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
Verified
Journal Article
Closed access
MJM Jermy
M Jermy
WHWei Hua Ho
Wei Hua Ho
Vortices can develop in the intakes of turbojet and turbofan aero engines during high power operation near solid surfaces such as during takeoff or ground tests. These vortices can stall the compressor and cause significant damage. The factors determining the formation of the vortex include engine thrust, distance from ground, and ambient vorticity. A computational fluid dynamics study was conducted to determine whether these effects could be predicted numerically, and the results were compared to previous wind-tunnel studies. This is the first reported study of numerical predictions of the vortex formation threshold. Two factors, which had not been previously studied either experimentally or numerically, were investigated: the effects of increasing the size of the suction inlet and increasing the thickness of the ground boundary layer. Both were found to encourage vortex formation. The threshold of vortex formation predicted numerically agrees with previous wind-tunnel studies, within the scatter of the experimental data. The numerical results reproduce all trends identified in the experimental studies. The minimum shear required to form a vortex was found, lying between 0.001 and 0.05/s (Rossby number of the order of 105).