Truong Do

Dr. Truong Do


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 October 2021 in Polymers
Verified
Journal Article
Open access
PDF file
CWChanglang Wu
Changlang Wu
TDTruong Do
Truong Do
PTPhuong T. Tran
Phuong T. Tran
This paper proposes a design of novel composite materials inspired by the Peano curve and manufactured using PolyJet 3D printing technology with Agilus30 (flexible phase) and VeroMagentaV (rigid phase) materials. Mechanical properties were evaluated through tensile and compression tests. The general rule of mixture (ROM) for composites was employed to approximate the tensile properties of the hybrid materials and compare them to the experimental results. The effect of reinforcement alignments and different hierarchies are discussed. The results indicated that the 5% inclusion of the Peano reinforcement in tensile samples contributed to the improvement in the elastic modulus by up to 6 MPa, but provided no obvious enhancement in ultimate tensile strength. Additionally, compressive strengths between 2 MPa and 6 MPa were observed for compression cubes with first-order reinforcement, while lower values around 2 MPa were found for samples with second-order reinforcement. That is to say, the first-order reinforcement has been demonstrated more effectively than the second-order reinforcement, given the same reinforcement volume fraction of 10% in compression cubes. Different second-order designs exhibited slightly different mechanical properties based on the ratio of reinforcement parallel to the loading direction.

27 September 2023 in Materials Science in Additive Manufacturing
Verified
Journal Article
Open access
PDF file
TLTian Lan
Tian Lan
CPChenxi Peng
Chenxi Peng
KFKate Fox
Kate Fox
TDTruong Do
Truong Do
PTPhuong T. Tran
Phuong T. Tran
In this work, we propose the strategies for designing radial graded sheet-based gyroid lattice and the approach to hybridizing solid-network-based gyroid lattice and primitive lattice. The elastic property of triply periodic minimal surfaces (TPMS) sheet-based gyroid lattice structures was explored. We also conducted numerical analysis to investigate the effect of functionally graded sheet-based gyroid lattices on the implant application, and explored the elastic properties of the uniform gyroid lattice parametrically with different relative densities based on the representative volume element model. Analytical equations based on the Gibson-Ashby model were generated to predict the elastic properties. Compressive tests on the samples fabricated by the Stratasys J750 were conducted to validate the feasibility of applying hybridization of different types of lattices. A comparison between radial hybrid primitive-gyroid and gyroid-primitive lattices revealed that the compressive behavior of gyroid-primitive was strengthened. We also found that the gyroid-primitive lattice could achieve auxetic compressive behavior. In conclusion, the numerical analysis illustrates that the application of the functional graded gyroid lattices can relieve the stress shielding effect as well as protects the bone from damage. The hybridization of different lattices can not only strengthen the mechanical properties of TPMS structures but also create a counter-intuitive deformation response.

7 May 2026 in Progress in Additive Manufacturing
Verified
Journal Article
Open access
PDF file
CPChenxi Peng
Chenxi Peng
TLTian Lan
Tian Lan
Hongxu WangHongxu Wang
Hongxu Wang
TDTruong Do
Truong Do
PTPhuong T. Tran
Phuong T. Tran
This paper investigates the design and mechanical behaviour of AlSi10Mg gyroid lattice structures under dynamic loading conditions. Triply periodic minimal surface (TPMS) gyroid lattices are generated based on the level-set approximation method and fabricated through powder bed fusion (PBF) with heat treatment. A numerical model is developed and validated by low-velocity impact drop-weight compression tests. High strain-rate-dependent materials model is investigated numerically following the validation of low velocity impact test. While local material could experience strain-rate effect, overcall lattices experience negligible influence of strain-rate. The study focuses on predicting deformation modes and the compressive response under impact loads using drop-weight tests and numerical simulations. Three distinct modes: homogeneous, transition, and shock are identified, each marked by different force-displacement behaviours and deformation behaviours. It is found that relative density significantly impacts mechanical performance, with higher densities leading to increased peak and mean crushing forces and more stable force-displacement curves. The structure with a graded relative density demonstrates improved deformation uniformity and stress distribution. The continuum-based shock model accurately predicts critical impact velocities corresponding to different deformation modes.

9 July 2026
Verified
Book Chapter
Closed access
PDF file
TLToan Luu
Toan Luu
VNVu Linh Nguyen
Vu Linh Nguyen
NGNguyen Huu Truong Giang
Nguyen Huu Truong Giang
TDTruong Do
Truong Do