Research on electromagnetic interference (EMI) of high frequency power converters remains a challenging and important topic, particularly in light of rapidly emerging wide bandgap power devices operating with ns level turn-on/turn-off times. Building on the substantial contributions that have been made on the formation mechanisms of common mode (CM) radiation, a new mechanism of equivalent CM driving voltage source caused by imbalanced conductors or components is proposed. Applying this mechanism, the CM driving voltage source model of a non-isolated Boost DC/DC power converter with input/output cables is introduced. The CM far field electric strength algorithms of an asymmetric cable antenna are theoretically analyzed and derived in detail. Subsequently, a prototype for a low-power 30 MHz very high frequency (VHF) Boost power converter based on gallium nitride (GaN) is built and its 10 m CM far field radiation strength is predicted according to the proposed model. The radiation pattern characteristics are analyzed and several radiation suppression methods are also designed. The comparison with the measured radiation results shows that the proposed CM radiation model and the prediction method achieve good effect below 300 MHz.
19 March 2020 in IEEE Transactions on Power Electronics
Broadband circuit models and their parameters of passive components are an important part of the functional design and electromagnetic compatibility analysis of power electronic devices. In this article, we propose a novel concise physical lumped-parameter extraction method for the construction of effective broadband circuit models for printed circuit board inductive components. The method is based on PEEC theory and generalized eigenvalue theory. The frequency domain port impedance characteristics are kept as equal as possible during circuit model transformation processes. A partial equivalent element circuit (PEEC) model of a three-dimensional PCB inductive component with a large number of nodes is first of all introduced. This includes conductors and PCB dielectrics. Then, its port impedance matrix formula is deduced. After this, the polynomial form of the port impedance matrix and the circuit model order reduction method are presented in detail. We report on the construction of two typical coreless PCB planar components, a spiral planar inductor and a coreless planar transformer, whose broadband physical circuit models and parameters were extracted using the proposed method. The results of tests with these two planar components confirmed the validity of their models for a frequency range of up to 500 MHz.
23 November 2022 in IEEE Transactions on Power Electronics
The far-field radiation generated by a power electronic converter with V-shaped cables is a key theoretical problem with engineering application significance. The irregular V-shaped antenna is very difficult to calculate analytically, making a precise prediction of the power converter's far-field radiation very challenging. In this work, the far-field radiation of a power converter with flat shielded cables is modeled and predicted using the retarded partial element equivalent circuit ( ${\mathbf{\tau}}$ PEEC) theory. The τPEEC modified node analysis circuit model of a metal radiator is introduced first, and then the radiator's input impedance formula is deduced. The τPEEC computation model of the V-shaped radiator, which includes the ground plane reflection effect, is developed for the typical far-field radiation test configuration, and the numerical calculation of the far-field radiation transfer function is obtained using the field strength sensor method. To test the suggested τPEEC approach, a 30-MHz low-side buck converter with flat shielded cables is built, and its 10-m far-field radiation strength is predicted. The V-shaped radiator's radiation characteristics are also investigated, and a design for suppression is proposed and demonstrated.
Common mode (CM) electromagnetic interference (EMI) has been a difficult subject in electromagnetic compatibility (EMC) analysis and design of power converters for electric vehicles (EV) because of its complex formation mechanism and hidden propagation path. This paper studies a new mechanism of CM conducted emission caused by the leakage flux of a toroidal inductor in the main circuit of a boost DC/DC converter. The stray magnetic source and the CM inducted loops are firstly identified out by simulation analysis and experiments. Then a comprehensive conducted emission circuit model including magnetic coupling parameters is built to explain this CM EMI formation mechanism. Finally, several effective magnetic coupling suppression methods are proposed and verified, such as changing the installation angle of the inductor and the shape of the magnetic core. The research results are helpful to the EMC understanding and design of power electronic converters.
It's well known a switched-mode power supply is easily to produce strong electromagnetic radiation emission and fails in EMC test for its RFI exceeding limits between 30MHz-200MHz. Based on asymmetry line antenna theory, a novel far field common mode radiation model, including an equivalent driving source, radiation structure and some key influence factors, is identified and built up for a small flyback power supply. Radiation characteristics of this model are predicted by using Ansoft HFSS and its effectiveness is verified by experiment. In the end, the radiation role of some key factors, such as the length of output cable, CM impedance of AC grid, layout of cable and reflected ground, are studied using simulation in detail.
1 September 2022 in Chinese Journal of Electrical Engineering
In this paper, common mode (CM) and differential mode (DM) far-field radiation models of a typical digital inverter with cables are built up to predict electromagnetic field strength and analyze field characteristics. The CM current model and its analyses are based on the imbalance difference method. It is found out that the voltage between the drain and the source electrodes of upper transistor is the key equivalent source of electromagnetic interference (EMI). Far-field radiation strength of the digital inverter in free space is predicted by using the asymmetrical antenna radiation method and current loop radiation method. The accuracy of these methods is verified by the CST electromagnetic simulation results in the frequency range from 1 MHz to 400 MHz. Furthermore, the radiation models are improved by using the mirror method, which enables to include the reflection effect of the metal ground plane at the electromagnetic compatibility (EMC) test site. Both the results of measurements in a semi-anechoic chamber and the simulation results confirm the proposed electromagnetic radiation prediction method.