We present a universal method of determining the position, 3D orientation, and relative quantum yield ratio (RQYR) of fluorescent nanoemitters (ZnS coated CdSe quantum dots) in a glass slide by combining laser scanning microscopy (LSM) and polarization measurements. The quantum dots were located through LSM intensity maps using azimuthal, radial, and linear incident polarizations. LSM imaging was not sufficient to determine the orientation of the quantum dots due to the isotropic absorption dipole moment. The 3D orientation was obtained through polarization measurement. By combining LSM and polarization measurements, the RQYR of a single molecule was evaluated, allowing us to compare the quantum yield of the nanoemitters.
Iron oxide nanostructures were synthesized using the carbothermal reaction of Fe microspheres generated by infrared pulsed laser ablation. The Fe microspheres were successfully deposited on Si(100) substrates by laser ablation of the Fe metal target using Nd:YAG pulsed laser operating at λ = 1064 nm. By varying the deposition time (number of pulses), Fe microspheres can be prepared with sizes ranging from 400 nm to 10 µm. Carbothermal reaction of these microspheres at high temperatures results in the self-assembly of iron oxide nanostructures, which grow radially outward from the Fe surface. Nanoflakes appear to grow on small Fe microspheres, whereas nanowires with lengths up to 4.0 μm formed on the large Fe microspheres. Composition analyses indicate that the Fe microspheres were covered with an Fe3O4 thin layer, which converted into Fe2O3 nanowires under carbothermal reactions. The apparent radial or outward growth of Fe2O3 nanowires was attributed to the compressive stresses generated across the Fe/Fe3O4/Fe2O3 interfaces during the carbothermal heat treatment, which provides the chemical driving force for Fe diffusion. Based on these results, plausible thermodynamic and kinetic considerations of the driving force for the growth of Fe2O3 nanostructures were discussed.
Laser-produced plasma (LPP) expansion and the subsequent shock wave propagation in a background gas have been extensively studied via experiments and simulations. However, the impact of the reflected shock wave on the incident plasma is rarely investigated despite its potential impact on the properties of the expanding LPP. Here, we use the direct simulation Monte Carlo (DSMC) method, implemented using the open-source DSMC code SPARTA, to model copper LPP expansion in a background gas and the subsequent shock wave formation, propagation, and reflection from a substrate. We simplify the computational framework by assuming normal evaporation during material ablation and using the initial plume dimensions, temperature, and number density as the input parameters for the DSMC model. The simulated plume expansion in vacuum agrees with an analytical solution for the gas dynamic equations at different target surface temperatures. Aside from the expected buffering effect of the background gas on the expanding plume, we also demonstrated that collision with the reflected shock wave further lowers the kinetic energy of the incoming plume. We compared the plume-shock interactions using argon and helium gas to explore the effect of varying mass ratios between the plume and background gas species. Finally, the Cu flux toward the substrate confirmed how the reflected shock wave compresses the incoming plume. These simulations exhibit the significant impact of the reflected shock wave on the plume dynamics near the substrate, which must be further studied to optimize LPP applications in material synthesis.
Femtosecond pulsed laser ablation (fs-PLA) is an interesting yet complicated field of study especially for undergraduate students entering the field. Hence, a bridging concept using classical and mechanical analog will be helpful. In this paper, we modelled the thermal energy transfer between electron and lattice system in a fs-PLA of metal described by two temperature model (TTM) using a coupled spring-mass oscillator. This was achieved by providing correspondence of TTM parameters to the coupled spring-mass oscillator, with temperature as position, electron thermal conductivity as coefficient of friction, electron-phonon coupling factor as spring term, electron/lattice heat capacity as the mass m1/m2 respectively, and laser source term as the driving force. The thermophysical properties considered are temperature dependent leading to position dependent parameters of coupled spring-mass oscillator. Results showed that the coupled spring-mass oscillator exhibit many behavior similar to the TTM. Additionally, maximum positions achieved by m2 behave similarly with maximum lattice temperature after achieving certain threshold value. However, many features of TTM such as spatial dependence and crater formation are not observed in the coupled spring-mass oscillator. Despite its limitation, the coupled spring-mass oscillator model was able to represent many features of the thermal energy transfer of fs-PLA, and could be an easy and useful model in understanding fs-PLA.