State Key Laboratory of Applied Optics, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033, China
Dr. Wenchao Zhou
State Key Laboratory of Applied Optics, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033, China
Curved compound eyes have generated great interest owing to the wide field of view but the application of devices is hindered for the lack of proper detectors. One-lens curved compound eyes with multi-focal microlenses provide a solution for wide field imaging integrated in a commercial photo-detector. However, it is still a challenge for manufacturing this kind of compound eye. In this paper, a rapid and accurate method is proposed by a combination of photolithography, hot embossing, soft photolithography, and gas-assisted deformation techniques. Microlens arrays with different focal lengths were firstly obtained on a polymer, and then the planar structure was converted to the curved surface. A total of 581 compound eyes with diameters ranging from 152.8 µm to 240.9 µm were successfully obtained on one curved surface within a few hours, and the field of view of the compound eyes exceeded 108°. To verify the characteristics of the fabricated compound eyes, morphology deviation was measured by a probe profile and a scanning electron microscope. The optical performance and imaging capability were also tested and analyzed. As a result, the ommatidia made up of microlenses showed not only high accuracy in morphology, but also imaging uniformity on a focal plane. This flexible massive fabrication of compound eyes indicates great potential for miniaturized imaging systems.
26 October 2020 in Journal of Lightwave Technology
In this article, we demonstrate an on-demand two-step fabrication strategy for optical microfiber couplers (OMCs) with precisely controlled dispersion turning points (DTPs). Firstly, an OMC with a relatively thick width is obtained through the fusion elongation method. Secondly, the as-fabricated OMC is placed in a low-concentration hydrofluoric acid solution whose refractive index (RI) is adjusted to match that of the target working environment to fine etch the width of the OMC. During the etching process, the real-time output spectrum of the OMC is monitored in-line to track the position of the OMC. The etching process is terminated once the desired DTP appears. Our study shows that by accurately controlling the reaction time, the DTP can be tuned from 1600 nm to 900 nm with high precision better than 1 nm in both water and a liquid medium with a high RI of 1.365. Finally, we experimentally demonstrate that the OMC fabricated by the proposed method can work as an ultrasensitive RI sensor with a sensitivity of -290000 nm/RIU at 1.333 and a biosensor for carcinoembryonic antigen (CEA) with a limit of detection of 2 pg/mL.
The thermal stability of DNA immobilized on a solid surface is one of the factors that affects the efficiency of solid-phase amplification (SP-PCR). Although variable temperature amplification ensures high specificity of the reaction by precisely controlling temperature changes, excessively high temperatures during denaturation can negatively affect DNA stability. Formamide (FA) enables DNA denaturation at lower temperatures, showing potential for SP-PCR. Research on FA’s impacts on DNA microarrays is still limited, necessitating further optimization in exploring the characteristics of FA in SP-PCR according to particular application needs. We immobilized DNA on a chip using a crosslinker and generated DNA microarrays through bridge amplification based on FA denaturation on our automated reaction device. We optimized the denaturation and hybridization parameters of FA, achieving a maximum cluster density of 2.83 × 104 colonies/mm2. Compared to high-temperature denaturation, FA denaturation required a lower template concentration and milder reaction conditions and produced higher cluster density, demonstrating that FA effectively improves hybridization rates on surfaces. Regarding the immobilized DNA stability, the FA group exhibited a 45% loss of DNA, resulting in a 15% higher DNA retention rate compared to the high-temperature group, indicating that FA can better maintain DNA stability. Our study suggests that using FA improves the immobilized DNA stability and amplification efficiency in SP-PCR.
The capture of individual cells using microfluidic chips represents a widely adopted and efficient approach for investigating the biochemical microenvironment of singular cells. While conventional methods reliant on boundary effects pose challenges in precisely manipulating individual cells, single-cell capture grounded in the principle of stagnation point flow offers a solution to this limitation. Nevertheless, such capture mechanisms encounter inconsistency due to the instability of the flow field and stagnation point. In this study, a microfluidic device for the stable capture of single cells was designed, integrating the principle of fluid mechanics by amalgamating stagnation point flow and boundary effects. This innovative microfluidic chip transcended the limitations associated with single methodologies, leveraging the strengths of both stagnation point flow and boundary effects to achieve reliable single-cell capture. Notably, the incorporation of capture ports at the stagnation point not only harnessed boundary effects but also enhanced capture efficiency significantly, elevating it from 31.9% to 83.3%, thereby augmenting capture stability. Furthermore, computational simulations demonstrated the efficacy of the capture ports in entrapping particles of varying diameters, including 9 μm, 14 μm, and 18 μm. Experiment validation underscored the capability of this microfluidic system to capture single cells within the chip, maintaining stability even under flow rate perturbations spanning from 60 μL/min to 120 μL/min. Consequently, cells with dimensions between 8 μm and 12 μm can be reliably captured. The designed microfluidic system not only furnishes a straightforward and efficient experimental platform but also holds promise for facilitating deeper investigations into the intricate interplay between individual cells and their surrounding microenvironment.
Metasurface regulates the polarization, phase, amplitude, frequency, and other characteristics of electromagnetic waves through the subwavelength microstructure. By using its polarization characteristics, it can realize the functions of optical rotation and vector beam generation. It is the most widely used method of regulation. However, parallel optical manipulation, imaging, and communication usually require polarization-insensitive focused (or vortex) arrays of beams, so polarization-independent wavelength multiplexing optical systems need to be considered. In this paper, the genetic algorithm combined with the computer-generated hologram (CGH) is used to control the transmission phase of the structure itself, and on the basis of wavelength multiplexing, the corresponding array of focused or vortex beams without the polarization selection property is realized. The simulation software results show that the method has a huge application prospect in optical communication and optical manipulation.