The aim of this paper was to study the effectiveness of a diode laser (LD) for removal of microorganisms isolated from porcelain and zirconia crown surfaces used in implantoprosthetics in order to minimize infections around dental implants. In order to optimize biocidal efficacy of the process (at the same time, avoiding increasing the surface roughness during decontamination) the effects of diode laser doses were investigated. The irradiation was performed with a diode laser at the wavelength of λ = 810 nm in three variants with a different number of repetitions (1 × 15 s, 2 × 15 s, 3 × 15 s). The quantitative microbial contamination of the surface of teeth, porcelain and zirconia crowns assessment was made using the culture-dependent method. The identification of microorganisms took place using the matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS) and next-generation sequencing (NGS) methods. The studies of the surface morphology and roughness were carried out by means of the optical profilometry, scanning electron microscopy (SEM) and optical microscopy with the C1 confocal attachment. The most important conclusion from the research is the fact that the laser operation, regardless of the exposure time, effectively eliminates the microorganisms from the surfaces used for dental implant rebuilding and does not have a destructive effect on the tested material.

Patients undergoing implant treatment are at risk of peri-implant bone loss, which is most often caused by the adverse effects of microorganisms, but there are few proven procedures for their reduction. The aim of the research was to identify the microorganisms inhabiting the composites used to close the screw access hole (SAH), compare them numerically with those present on the surface of crowns and teeth, and optimize the doses of the diode laser, which will reduce microorganisms and will not deteriorate the roughness of polished composites. Patients were swabbed from the surface of SAH composites, from porcelain and zirconium restorations, and from teeth, and then the number of microorganisms was determined by using a culture technique. Microorganisms were identified by MALDI–TOF MS and NGS sequencing. The effectiveness of diode laser irradiation was achieved by using four variants of exposure. After polishing and laser irradiation, the surface roughness of the composites was studied by using optical profilometry. On the surface of SAH, 10⁶ to 10⁸ microorganisms were identified at 0.4 cm², including many pathogenic species. Among the materials used for the reconstruction of dental implants, the greatest microbiological contamination was found on the composites used to close the SAH. The diode laser with a wavelength of 810 nm with an average power of 3.84 W, during 60 s and 2 × 30 s, has a biocidal effect and does not significantly change the surface roughness of composites. The best reduction of microorganisms was achieved on a composite polished with a polishing rubber and then with a Sof-Lex™ Pre-Polishing Spiral beige (3M ESPE, Ave. St. Paul., MN, USA). Studies have shown that using the optimal laser dose can help treat periimplantitis. These studies provide important information on the possibility of the effective elimination of microorganisms by using a diode laser in the treatment of peri-implant bone loss.

Gingivitis is accompanied by microorganisms, including pathogens, which must be eliminated to speed up the treatment of inflammation. Laser irradiation may be one of the safe methods for reducing tissue contamination on the tooth surface. The aim of the study was the assessment of the tooth surface in patients with gingivitis after the use of a diode laser to eliminate microorganisms living there. In the first stage of the research, microorganisms were isolated (Candida albicans, C. guilliermondii, Escherichia coli, Haemophilus parainfluenzae, Klebsiella oxytoca, Neisseria subflava, Rothia dentocariosa, Rothia mucilaginosa, Streptococcus pneumoniae) from three patients with gingivitis, their identification confirmed using the MALDI-TOF MS technique (matrix-assisted laser desorption/ionisation time-of-flight mass spectrometry). Then, the irradiation process with a diode laser was optimized to a wavelength of 810 nm ± 10 nm in five variants to reduce microorganisms on the tooth. The tooth surface was analyzed by X-ray photoelectron spectroscopy (XPS) and optical profilometry (OP) before and after irradiation. 103 to 106 CFU were detected on a 0.4 cm² tooth area. Nine types of bacteria and two types of fungi dominated among the microorganisms. The laser at the most effective biocidal dose of 25 W/15.000 Hz/10 µs, average = 3.84 W, with three uses after 15 s, increased the reduction of fungi from 57.97% to 93.80%, and bacteria from 30.67% to 100%. This dose also caused a decrease in the degree of oxidation and in the effect of smoothing on the treated surfaces.