Masayuki Mizuno

Prof. Dr. Masayuki Mizuno

Tokyo University of Science, Tokyo, Japan
orcid

Research Focus & Metrics

Academic Career Length

31Years (1996-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 1996 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
TIT. Iima
T. Iima
MMMasayuki Mizuno
Masayuki Mizuno
THT. Horiuchi
T. Horiuchi
MYM. Yamashina
M. Yamashina

1 January 2000
Verified
Conference Paper
Closed access
NNN. Nishi
N. Nishi
TITomoo Inoue
Tomoo Inoue
MNM. Nomura
M. Nomura
SMS. Matsushita
S. Matsushita
STS. Torii
S. Torii
MFM. Fukuma
M. Fukuma
A 125 MHz 1 GIPS at 1.3 V 1 W microprocessor with single-chip tightly-coupled multiprocessor architecture and low-voltage circuits is targeted to high-performance and low-power embedded systems, especially smart information terminals. This paper shows an entire chip diagram integrating four tightly-coupled processors. Each processing element (PE) is in-order two-way issue superscalar with two ALU pipelines. A power-management unit (PMU) cuts off the leakage current of each power-control domain independently using dedicated power switches.

23 December 2002
Verified
Conference Paper
Closed access
MMMasayuki Mizuno
Masayuki Mizuno
KFK. Furuta
K. Furuta
SNS. Narita
S. Narita
HAH. Abiko
H. Abiko
ISI. Sakai
I. Sakai
MYM. Yamashina
M. Yamashina

20 June 2024 in Indoor and Built Environment
Verified
Journal Article
Closed access
SPSeongKyung Park
SeongKyung Park
GWGuan-Yuan WU
Guan-Yuan WU
KFKosuke Fujii
Kosuke Fujii
MMMasayuki Mizuno
Masayuki Mizuno
In a fire, stairways are the primary avenues for building evacuation. Previous studies focused on investigating evacuation flow through evacuation drills in a high-rise office building to assess the accuracy of evacuation scenarios and compared them with evacuation dynamics. However, the effectiveness of evacuation drills in estimating many scenarios is limited by actual drills. The evacuation simulations present a promising approach to objectively evaluating evacuation scenarios. This study verifies whether evacuation simulations can faithfully replicate actual evacuation flow and effectively predict suitable evacuation scenarios or potentially involve parameter calibration. Through a comprehensive comparison analysis, this study scrutinized the reliability of evacuation simulations and calibrated the simulation parameters. The analysis revealed that factors, including adjustments to the door width, personal space considerations for occupants in both conflict and normal situations and variations in staircase structure configuration, can significantly influence the evacuation flow within staircases. Manipulating these parameters in simulations would enable a more precise replication of evacuation flow within staircases, thereby enhancing the simulation’s accuracy in target evacuation scenarios. The findings of this research have underscored the significance of employing advanced simulation techniques to model evacuation dynamics accurately, facilitating a robust framework for devising effective emergency evacuation strategies in high-rise office buildings.

2 November 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Kye-Won PARKKye-Won PARK
Kye-Won PARK
MMMasayuki Mizuno
Masayuki Mizuno
CCChang-Geun Cho
Chang-Geun Cho
JJJong-jin Jeong
Jong-jin Jeong
The population density of cities has been increasing with time and the development of industry. Building fires in large cities with high population density cause extensive human and property damage. To prevent such damage, the characteristics of flames such as the thermal radiation and intensity of the fire source must be considered when designing building structures. However, the consideration of these factors is practically inadequate. Accordingly, in this study, when a mattress was ignited in an open environment at a different installation height (0–515 mm), the measurements from a heat flux meter and the calculated thermal radiation were compared, and a comparative analysis was conducted using the existing prediction formulas by researchers described in ISO 24678-7. We examined the fire risk of mattresses according to the mattress installation height. As a result, the fire risk of the mattress was confirmed according to the mattress installation height; upon comparing the experimental and calculated values for radiant heat, it was found to be necessary to estimate the radiant heat using a calculation method that applies the configuration factor differently depending on the change in the flame shape. In addition, as a result of substituting the experimental value into the calculation method of ISO 24678-7 (a method for estimating the radiant heat of liquid combustibles), the experimental value and the calculated value were found to be significantly different. Therefore, similar to ISO 24678-7 for the radiation heat estimation method for “liquid combustibles”, an international standard for establishing the radiation heat estimation method for “solid combustible materials” as a standard was also required for a reasonable analysis of the fire safety phenomenon of solid materials, such as bed mattresses.

24 May 2022 in Materials
Verified
Journal Article
Open access
PDF file
JJJong-jin Jeong
Jong-jin Jeong
MMMasayuki Mizuno
Masayuki Mizuno
Kye-Won PARKKye-Won PARK
Kye-Won PARK
HLHyeon-Jin Lim
Hyeon-Jin Lim
CCChang-Geun Cho
Chang-Geun Cho
Bed mattresses are rated as products to cause a fire hazard because of their very high heat release rate among indoor combustibles. In this study, fire growth rate and flame height were measured through a series of combustion experiments on a full scale in order to provide information regarding mattress fire characteristics. The experiments were conducted in an open space, and bed mattresses as the test samples were installed at different installation heights (0~515 mm). The experiment results revealed that the higher the bed mattress was installed, the higher the fire growth rate, the heat release rate, and the flame height. Additionally, the time of the mattress to reach 1 MW was evaluated as the category “medium” in the NFPA 72 standards. The flame heights showed a good coincidence compared to the existing flame height model equations, proving the applicability of the model to the mattress combustion.