Application of low-cost carbon black from lignin highly depends on the materials properties, which might by determined by raw material and processing conditions. Four different technical lignins were subjected to thermostabilization followed by stepwise heat treatment up to a temperature of 2000 °C in order to obtain micro-sized carbon particles. The development of the pore structure, graphitization and inner surfaces were investigated by X-ray scattering complemented by scanning electron microscopy and FTIR spectroscopy. Lignosulfonate-based carbons exhibit a complex pore structure with nanopores and mesopores that evolve by heat treatment. Organosolv, kraft and soda lignin-based samples exhibit distinct pores growing steadily with heat treatment temperature. All carbons exhibit increasing pore size of about 0.5–2 nm and increasing inner surface, with a strong increase between 1200 °C and 1600 °C. The chemistry and bonding nature shifts from basic organic material towards pure graphite. The crystallite size was found to increase with the increasing degree of graphitization. Heat treatment of just 1600 °C might be sufficient for many applications, allowing to reduce production energy while maintaining materials properties.
Various methods are available for the calculation of timber–concrete composite floors. The gamma method, which is important in construction practice, as well as the differential equation method, are based on the simplified assumption of a continuous bond between wood and concrete. This makes it possible to analytically calculate the internally statically indeterminate partial section sizes and deformation sizes, analogous to the force size method. In this paper, two typical load situations of concentrated loads (central and off-centre) were analytically and numerically evaluated and compared using the above-mentioned methods (gamma and differential equation), with a discrete method for the case of a timber beam reinforced with a concrete slab using screws as fasteners. The calculation results show significant deviations, which speak for the application of discrete methods in certain load situations and thus limit the usability of the gamma method under certain conditions. For the problem of deflection determination, which is not dealt with in the literature for the discrete method, a numerical method is described in the present work, which was first developed and presented by the first author.
In the case of load increases and the refurbishment of existing buildings, it is often necessary to carry out strengthening measures on existing timber beams. When timber concrete composite (TCC) ceilings cannot be used, it is possible to reinforce the undersides of the beams with structural steel or fiber composites (aramid or carbon-fiber-reinforced polymer). This work investigates how significant effects on the load-bearing and deformation behavior can be achieved with these materials in terms of construction practice. The article is intended to show structural engineers which reinforcement measures lead to which forces, deformations, etc., and how these are utilized. This should form the basis for the planning of reinforcement measures, as it is not clear from the beginning whether AFRP, CFRP, or steel is the most suitable material. For this purpose, a comparative parameter study was carried out under practical conditions and with a variable degree of reinforcement using the corresponding formulas. The internal forces in the timber and reinforcement cross-sections, the deflection behavior, and the failure loads at the strength and design levels were calculated. It was demonstrated that, particularly for steel and carbon-fiber-reinforced polymer (CFRP) reinforcements, significant increases in the ultimate load can be achieved and the often-important deformation behavior can be significantly improved. Especially the steel variant leads to high improvements in deflection and breaking load behavior, with the base material (wood) also being utilized more economically as a result. A comparative ecological study in the form of the global warming potential showed that reinforcement methods are also advantageous from the point of view of sustainability compared to renovations with timber concrete composite slabs or new concrete slabs.
Historic unreinforced masonry (URM) buildings from the “Gründerzeit” period (≈ 1840–1918) of the Austro-Hungarian Monarchy represent a substantial part of Vienna’s building stock and are particularly vulnerable to seismic action. While strong earthquakes in the Vienna Basin are infrequent, historical records demonstrate that the regional seismic hazard remains relevant. This study presents a systematic evaluation of the seismic vulnerability of historic brick masonry buildings under varying structural configurations. The analysis is based on a detailed assessment of the structural system that defines key parameters of this building type. To capture the material variability typically observed in historic masonry, an extensive in-situ testing campaign was conducted on more than 200 URM buildings across Vienna, comprising over 2000 sampling locations. Non-linear static analyses (pushover) were performed using the 3Muri software on a representative reference case study building reflecting the typical structural characteristics of Viennese URM structures. A parametric study was conducted to investigate the influence of building height, masonry quality and floor configuration on the seismic performance of these historic buildings. This approach enables a targeted evaluation of structural uncertainty and a comprehensive assessment across a wide range of configurations. Further, fragility curves were derived to quantify the effect of each parameter on the probability of exceeding specific damage thresholds. The results confirm that low masonry quality and increased building height significantly amplify seismic vulnerability of historic URM buildings, whereas typical variations in floor configurations have only minor impact. These findings emphasise the importance of robust on-site experimental investigations to accurately characterise material properties and thereby enhance the reliability of vulnerability assessments. Moreover, the study highlights the limitations of simplified typology-based approaches and provides a solid basis for improved risk evaluation, retrofit prioritisation and seismic mitigation strategies.