In this study, some crucial parameters were determined of flexible polymer–organic solar cells prepared from an active layer blend of poly(3-hexylthiophene) (P3HT) and the fullerene derivative [6,6]-phenyl-C₆₁-butyric acid methyl ester (PCBM) mixed in 1:1 mass ratio and deposited from chlorobenzene solution by spin-coating on poly(ethylene terephthalate) (PET)/ITO substrates. Additionally, the positive effect of an electron transport layer (ETL) prepared from zinc oxide nanoparticles (ZnO np) on flexible photovoltaic elements’ performance and stability was investigated. Test devices with above normal architecture and silver back electrodes deposed by magnetron sputtering were constructed under environmental conditions. They were characterized by current-voltage (I–V) measurements, quantum efficiency, impedance spectroscopy, surface morphology, and time–degradation experiments. The control over morphology of active layer thin film was achieved by post-deposition thermal treatment at temperatures of 110–120 °C, which led to optimization of device morphology and electrical parameters. The impedance spectroscopy results of flexible photovoltaic elements were fitted using two R||CPE circuits in series. Polymer–organic solar cells prepared on plastic substrates showed comparable current–voltage characteristics and structural properties but need further device stability improvement according to traditionally constructed cells on glass substrates.

Targeting tumor cell mitochondria is a prospective strategy for highly effective anticancer therapy. Consequently, the development of potent systems for the targeted delivery of mitochondria-acting therapeutics to mitochondria has the potential to boost this sector of nanomedicine. In this study, a functional mixed micellar system based on two co-assembled triblock copolymers, poly(2-(dimethylamino)ethyl methacrylate)-b-poly(ε-caprolactone)-b-poly(2-(dimethylamino)ethyl methacrylate) bearing triphenylphosphonium ligands (PDMAEMA^(TPP+) ₂₀-b-PCL₇₀-b-PDMAEMA^(TPP+) ₂₀) and poly(ethylene oxide)-b-poly(ε-caprolactone)-b-poly(ethylene oxide) (PEO₁₁₃-b-PCL₇₀-b-PEO₁₁₃), was assessed for the mitochondria targeted delivery of curcumin. The high proapoptotic activity of the system and the sub-cellular mechanisms of cytotoxicity were demonstrated using a chemosensitive HL-60 cell line and its resistant alternative HL-60/DOX. Next, the successful localization of nanocarriers in mitochondria was proved by fluorescence microscopy with the aid of DAPI (4′,6-diamidino-2-phenylindole) as a cellular localization tracker. The in vitro experiments revealed the great potential of the functional system developed for the targeted delivery of curcumin to mitochondria, causing programmed tumor cell death.

The use of biodegradable polyesters derived from green sources and their combination with natural abundantly layered aluminosilicate clay, e.g., natural montmorillonite, meets the requirements for the development of new sustainable, disposable, and biodegradable organic dye sorbent materials. In this regard, novel electrospun composite fibers, based on poly β-hydroxybutyrate (PHB) and in situ synthesized poly(vinyl formate) (PVF), loaded with protonated montmorillonite (MMT-H) were prepared via electrospinning in the presence of formic acid, a volatile solvent for polymers and a protonating agent for the pristine MMT-Na. The morphology and structure of electrospun composite fibers were investigated through SEM, TEM, AFM, FT-IR, and XRD analyses. The contact angle (CA) measurements showed increased hydrophilicity of the composite fibers incorporated with MMT-H. The electrospun fibrous mats were evaluated as membranes for removing cationic (methylene blue) and anionic (Congo red) dyes. PHB/MMT 20% and PVF/MMT 30% showed significant performance in dye removal compared with the other matrices. PHB/MMT 20% was the best electrospun mat for adsorbing Congo red. The PVF/MMT 30% fibrous membrane exhibited the optimum activity for the adsorption of methylene blue and Congo red dyes.

Cannabidiol (CBD) is a natural terpenophenolic compound with known pharmacological activities, but the poor solubility of CBD in water limits its widespread use in medicine and pharmacy. Polymeric (nano)carriers demonstrated high potential for enhancing the solubility and therapeutic activity of lipophilic drugs such as CBD. Here, we report the elaboration of a novel hydroxypropyl cellulose (HPC)-based in situ gelling formulation for controlled delivery of CBD. In the first stage, nanosized polymeric micelles from poly(ethylene oxide)-block-poly(α-cinnamyl-ε-caprolactone-co-ε-caprolactone) (PEO-b-P(CyCL-co-CL) diblock copolymers) were used to increase the solubility of CBD in water. Different copolymers were assessed, and the carrier with the highest encapsulation efficiency (EE) and drug loading capacity (DLC) was selected for further elaboration of nanocomposite in situ gel formulations. Next, the sol-to-gel transition behavior of HPC as a function of K₂SO₄ concentration in the aqueous solution was investigated by microcalorimetry and dynamic oscillatory rheology, and the optimal formulation capable of forming a physical gel under physiological conditions was determined. Finally, injectable nanocomposite hydrogels comprising cannabidiol were fabricated, and their drug release profile and cytotoxicity against human tumor cell lines were evaluated. The in situ gels exhibited prolonged drug release over 12 h, controlled by gel erosion, and the cytotoxicity of formulated cannabidiol was comparable with that of a free drug.

Polymer micelles represent one of the most attractive drug delivery systems due to their design flexibility based on a variety of macromolecular synthetic methods. The environmentally safe chemistry in which the use or generation of hazardous materials is minimized has an increasing impact on polymer-based drug delivery nanosystems. In this work, a solvent-free green synthetic procedure was applied for the preparation of an amphiphilic diblock copolymer consisting of biodegradable hydrophobic poly(acetylene-functional carbonate) and biocompatible hydrophilic polyethylene glycol (PEG) blocks. The cyclic functional carbonate monomer 5-methyl-5-propargyloxycarbonyl-1,3-dioxane-2-one (MPC) was polymerized in bulk using methoxy PEG-5K as a macroinitiator by applying the metal-free organocatalyzed controlled ring-opening polymerization at a relatively low temperature of 60 °C. The functional amphiphilic block copolymer self-associated in aqueous media into stable micelles with an average diameter of 44 nm. The copolymer micelles were physico-chemically characterized and loaded with the plant-derived anticancer drug curcumin. Preliminary in vitro evaluations indicate that the functional copolymer micelles are non-toxic and promising candidates for further investigation as nanocarriers for biomedical applications.

We report the elaboration of redox-responsive functional micellar nanocarriers designed for triggered release of caffeic acid phenethyl ester (CAPE) in cancer therapy. Three-layered micelles, comprising a poly(ε-caprolactone) (PCL) core, a middle poly(acrylic acid)/poly(ethylene oxide) (PAA/PEO) layer and a PEO outer corona, were prepared by co-assembly of PEO₁₁₃-b-PCL₃₅-b-PEO₁₁₃ and PAA₁₃-b-PCL₃₅-b-PAA₁₃ amphiphilic triblock copolymers in aqueous media. The preformed micelles were loaded with CAPE via hydrophobic interactions between the drug molecules and PCL core, and subsequently crosslinked by reaction of carboxyl groups from PAA and a disulfide crosslinking agent. The reaction of crosslinking took place in the middle layer of the nanocarriers without changing the encapsulation efficiency (EE~90%) of the system. The crosslinked polymeric micelles (CPMs) exhibited superior structural stability and did not release CAPE in phosphate buffer (pH 7.4). However, in weak acidic media and in the presence of 10 mM reducing agent (dithiothreitol, DTT), the payload was released at a high rate from CPMs due to the breakup of disulfide linkages. The physicochemical properties of the nanocarriers were investigated by dynamic and electrophoretic light scattering (DLS and ELS) and atomic force microscopy (AFM). The rapid release of CAPE under intracellular-like conditions and the lack of premature drug release in media resembling the blood stream (neutral pH) make the developed CPMs a promising candidate for controllable drug release in the microenvironment of tumors.