There have been significant developments in the enhancement of the thermoelectric (TE) performances of p-type PbTe compounds; however, the TE performances of n-type compounds are not comparable with those of p-type ones. For optimizing the high performance, effective Fermi level tuning is critical. Here, we found that extrinsic doping caused complex defect configurations, resulting in unconventional lattice dynamics and abnormal electronic/thermal transport properties. From the formation energy calculation, the increase in the lattice parameter of PbTe compounds having excess Pb was correlated with the formation of interstitials (Pbint and Teint), Pb–Te antisite defects, and cluster-type defects [(PbTe–TePb), (Pb–Pb)Te, (Te–Te)Pb, and (Pbint–2PbTe)]. When we applied extrinsic n-type doping such as excess Pb and Bi doping, counterpart hole doping-type complex defects were easily generated. The charge compensation effects due to the intrinsic defects such as the VTe2+ and Pbint2+ point defects and cluster-type anionic defects such as Pbint–2(PbTe) resulted in an unconventional electrical transport behavior with respect to the excess Pb concentration in Pb1+xTe. Bi doping in Pb1−xBixTe also gave rise to complex cluster-type defects such as nBiPb–VPb (n = 2 and 3) simultaneously. The complex cluster-type defects not only suppressed the doping efficiency but also increased the scattering exponent in the Seebeck coefficient, resulting in the enhancement of the Seebeck coefficient. The charge compensation between the charged impurity and defect cluster doping was beneficial for fine tuning of the Fermi level for optimal carrier concentration.
22 July 2019 in Journal of the Korean Physical Society
The enormous progress achieved with high‐performance thermoelectric materials has yet to be implemented in high‐performance devices. The bottleneck for this is the material‐specific design of the interface between the thermoelectric material and the electrical connections, particularly identifying suitable contacting electrodes. This has mainly been empirical, slowing down device maturation due to the vast experimental space. To overcome this, an electrode pre‐selection method based on first‐principles electronic structure calculations of charged defect formation energies is established in this work for the first time. Such method allows to predict thermoelectric leg degradation due to impurity diffusion from the electrode into the thermoelectric material and formation of charge carrier traps, causing a majority carrier compensation and performance deterioration. To demonstrate the feasibility of this approach, the charged point defect formation energies of relevant metal electrodes with Mg2(Si,Sn) are calculated. Five hundred ten defect configurations are investigated, and the interplay between intentional doping and electrode‐induced point defects is predicted. These predictions are compared with Seebeck microprobe measurements of local carrier concentrations near the Mg2(Si,Sn)‐electrode interface and a good match is obtained. This confirms the feasibility of electrode screening based on defect formation energy calculations, which narrows down the number of potential electrodes and accelerates device development.
Thermoelectric generators are a reliable and environmentally friendly source of electrical energy. A crucial step for their development is the maximization of their efficiency. The efficiency of a TEG is inversely related to its electrical contact resistance, which it is therefore essential to minimize. In this paper, we investigate the contacting of an Al electrode on Mg2(Si,Sn) thermoelectric material and find that samples can show highly asymmetric electrical contact resistivities on both sides of a leg (e.g., 10 µΩ·cm2 and 200 µΩ·cm2). Differential contacting experiments allow one to identify the oxide layer on the Al foil as well as the dicing of the pellets into legs are identified as the main origins of this behavior. In order to avoid any oxidation of the foil, a thin layer of Zn is sputtered after etching the Al surface; this method proves itself effective in keeping the contact resistivities of both interfaces equally low (<10 µΩ·cm2) after dicing. A slight gradient is observed in the n-type leg’s Seebeck coefficient after the contacting with the Zn-coated electrode and the role of Zn in this change is confirmed by comparing the experimental results to hybrid-density functional calculations of Zn point defects.
In this study, the effect of Ag defects on the lattice and thermoelectric properties of Ag-doped BixSb2−xTe3 (BST) alloys are systematically investigated. Using density-functional calculations, we reveal that Ag impurity defects occupying interstitial sites in the BST affect the formation of intrinsic defects in the host materials. Ag interstitial defects, which are responsible for increasing the lattice parameter of the c axis, lower the formation energies of BiTe and SbTe acceptor defects more effectively in the Bi-rich BST than in the Bi-poor BST. In addition, these Ag interstitials induce the formation of AgBi and AgSb in BixSb2−xTe3. Therefore, Ag-induced defect interactions can be used to finely optimize the defects and doping density by varying the Bi content. Furthermore, the phonon thermal conductivity is reduced with the formation of nanoscale twin structures with various stacking faults. Finally, a high figure of merit of 1.4 at 423 K is achieved for p-type BST alloys.