The Zagreb 2020 earthquake severely damaged the historic centre of the city. Most of the damage occurred on historic masonry residential buildings, many of which are situated very close to the tram track. Although traffic-induced vibrations generally do not affect surrounding buildings, they can be harmful to buildings damaged by a previous earthquake. Vibrations could contribute to the further propagation of existing cracks. The effect of vibrations depends on many factors, one of the most important being the distance between the track and the building. The vibrations are highest at the source, and the energy loss occurs due to transfer through the soil to the recipients. The impact of tram-induced vibrations on earthquake-damaged buildings in the city of Zagreb is investigated in this paper. The analysis is conducted on a tramway network scale to identify critical locations by performing continuous monitoring on the tramway network and risk analysis based on the distance of buildings from the track, vibration amplitude at source, and building damage. Further investigation is based on the level of buildings to evaluate the influence of vibrations on actual buildings damaged in the Zagreb earthquake. Based on detailed signal analysis, the vibration characterization is performed, and the influence on damaged masonry buildings is evaluated.

Tram system is a backbone of public transportation in the City of Zagreb. In the last decade, its fleet has been renewed by 142 new low-floor trams. Shortly after their introduction, it was observed that they have a negative impact on the exploitation behavior of tram infrastructure, primarily on the durability of rail fastening systems. Because of that, it was decided to modify existing rail fastening systems to the new track exploitation conditions. When the (re)construction of tram infrastructure is carried out by applying new systems and technologies, it is necessary to take into account their impact on the future propagation of noise and vibration in the environment. This paper gives a short overview of the characteristics of the two newly developed rail fastening systems for Zagreb tram tracks, their application in construction of experimental track section, and performance and comparison of noise and vibration measurements results. Measured data on track vibrations and noise occurring during passage of the tram vehicles is analyzed in terms of track decay rates and equivalent noise levels of passing referent vehicle. Vibroacoustic performance of new fastening systems is evaluated and compared to referent fastening system, in order to investigate their ability to absorb vibration energy induced by tram operation and to reduce noise emission.

Electrical resistance is among the characteristics that fastening systems must meet to ensure the proper functioning of signaling systems in railway infrastructure. The EN 13146-5:2012 standard specifies a laboratory testing method for determining the electrical resistance under wet conditions between running rails provided by a fastening system on steel or concrete sleepers. In urban railway tracks, the electrical resistance of fastening systems affects the stray current; however, there is no standardized electrical resistance measuring method. There is also no definition for the minimum value that the electrical resistance of fastening systems must satisfy to prevent stray currents. For this reason, this paper analysis the possibility of using the standard EN 13146-5:2012 for the measurement and analysis of the electrical resistance of fastening systems in urban railway tracks. In this study, the electrical resistance of different fastening systems used in urban railway tracks was measured. Based on the tests results, the modifications needed in the EN 13146-5 standard for it to be suitable for urban railway tracks were identified. The proposed modifications include the use of a DC current source. The test should be performed on a rail sample fastened to the concrete base, and the current circuit should be closed by the reference electrode installed in the base. Spraying water from nozzles is not applicable for this measurement. The test should be performed under dry conditions and at different water levels (water on the top of the concrete base and on the top of the levelling layer). Different water levels were used to simulate the most common conditions in urban railway tracks built as part of the road surface, where the track-drying process is very slow. The test should not be performed when the rails are immersed in water, because the current flows directly from the rail into the water in such case, and the fastening system has no influence on the measured electrical resistance value. In addition to describing the proposed changes, the calculation of the minimum electrical resistance value that fastening systems in urban railway tracks must satisfy is also presented.

Rail corrugation and roughness represent typical irregularities on railway and tramway tracks, which cause increased dynamic forces, high-frequency vibrations, reduced riding comfort, shorter track lifespan, higher maintenance costs, and increased noise levels. Roughness and corrugation can be measured by evaluating the unevenness of the rail longitudinal running surface, which can be conducted using handheld devices or trolleys (directly on the track). Alternatively, vehicle or track-based indirect methods offer practical solutions for determining the condition of the rail running surface. This paper presents a methodology for rail corrugation and roughness evaluation, using bogie frame vibration data from an instrumented in-service tramway vehicle operating on Zagreb’s tramway network. Furthermore, it investigates the effects of various factors on the evaluation method, including wheel roughness, lateral positioning, signal processing methods, horizontal geometry, wheel–rail contact force, and tramway vehicle vibroacoustic characteristics. It was concluded that a simplified methodology that did not include transfer functions or wheel roughness measurements yielded relatively good results for evaluating rail corrugation and roughness across several wavelength bands. To improve the presented methodology, future research should assess the vehicle’s vibroacoustic characteristics with experimental hammer impact tests, measure the influence of wheel roughness on wheel–rail contact and bogie vibrations, and refine the measurement campaign by increasing test runs, limiting speed variation, and conducting controlled tests.