Detection and interpretation of human activities have emerged as a challenging healthcare problem in areas such as assisted living and remote monitoring. Besides traditional approaches that rely on wearable devices and camera systems, WiFi-based technologies are evolving as a promising solution for indoor monitoring and activity recognition. This is, in part, due to the pervasive nature of WiFi in residential settings such as homes and care facilities, and the unobtrusive nature of WiFi-based sensing. Advanced signal processing techniques can accurately extract WiFi channel status information (CSI) using commercial off-the-shelf devices or bespoke hardware. This includes phase variations, frequency shifts, and signal levels. In this article, we describe the healthcare application of Doppler shifts in the WiFi CSI caused by human activities that take place in the signal coverage area. The technique is shown to recognize different types of human activities and behavior and be very suitable for applications in healthcare. Three experimental case studies are presented to illustrate the capabilities of WiFi CSI Doppler sensing in assisted living and residential care environments. We also discuss the potential opportunities and practical challenges for realworld scenarios.

Human sensing using WiFi signal transmissions is attracting significant attention for future applications in e-healthcare, security, and the Internet of Things (IoT). The majority of WiFi sensing systems are based around processing of channel state information (CSI) data which originates from commodity WiFi access points (APs) that have been primed to transmit high data-rate signals with high repetition frequencies. However, in reality, WiFi APs do not transmit in such a continuous uninterrupted fashion, especially when there are no users on the communication network. To this end, we have developed a passive WiFi radar system for human sensing which exploits WiFi signals irrespective of whether the WiFi AP is transmitting continuous high data-rate Orthogonal Frequency-Division Multiplexing (OFDM) signals, or periodic WiFi beacon signals while in an idle status (no users on the WiFi network). In a data transmission phase, we employ the standard cross ambiguity function (CAF) processing to extract Doppler information relating to the target, while a modified version is used for lower data-rate signals. In addition, we investigate the utility of an external device that has been developed to stimulate idle WiFi APs to transmit usable signals without requiring any type of user authentication on the WiFi network. In this article, we present experimental data which verifies our proposed methods for using any type of signal transmission from a standalone WiFi device, and demonstrate the capability for human activity sensing.

Radio-frequency-based noncooperative monitoring of humans has numerous applications ranging from law enforcement to ubiquitous sensing applications such as ambient assisted living and biomedical applications for nonintrusively monitoring patients. Large training datasets, almost unlimited memory capacity, and ever-increasing processing speeds of computers could drive forward the data-driven deep-learning-focused research in the abovementioned applications. However, generating and labeling large volumes of high-quality, diverse radar datasets is an onerous task. Furthermore, unlike the fields of vision and image processing, the radar community has limited access to databases that contain large volumes of experimental data. Therefore, in this article, we present an open-source motion capture data-driven simulation tool, SimHumalator, that can generate large volumes of human micro-Doppler radar data in passive WiFi scenarios. The simulator integrates IEEE 802.11 WiFi Standards (IEEE 802.11 g, n, and ad) compliant transmissions with the human animation data to generate the micro-Doppler features that incorporate the diversity of human motion characteristics and the sensor parameters. The simulated signatures have been validated with experimental data gathered using an in-house-built hardware prototype. This article describes simulation methodology in detail and provides case studies on the feasibility of using simulated micro-Doppler spectrograms for data augmentation tasks.

This paper presents a comprehensive dataset intended to evaluate passive Human Activity Recognition (HAR) and localization techniques with measurements obtained from synchronized Radio-Frequency (RF) devices and vision-based sensors. The dataset consists of RF data including Channel State Information (CSI) extracted from a WiFi Network Interface Card (NIC), Passive WiFi Radar (PWR) built upon a Software Defined Radio (SDR) platform, and Ultra-Wideband (UWB) signals acquired via commercial off-the-shelf hardware. It also consists of vision/Infra-red based data acquired from Kinect sensors. Approximately 8 hours of annotated measurements are provided, which are collected across two rooms from 6 participants performing 6 daily activities. This dataset can be exploited to advance WiFi and vision-based HAR, for example, using pattern recognition, skeletal representation, deep learning algorithms or other novel approaches to accurately recognize human activities. Furthermore, it can potentially be used to passively track a human in an indoor environment. Such datasets are key tools required for the development of new algorithms and methods in the context of smart homes, elderly care, and surveillance applications.

This paper proposes a passive Doppler radar as a non-contact sensing method to capture human body movements, recognize respiration, and physical activities in e-Health applications. The system uses existing in-home wireless signal as the source to interpret human activity. This paper shows that passive radar is a novel solution for multiple healthcare applications which complements traditional smart home sensor systems. An innovative two-stage signal processing framework is outlined to enable the multi-purpose monitoring function. The first stage is to obtain premier Doppler information by using the high speed passive radar signal processing. The second stage is the functional signal processing including micro Doppler extraction for breathing detection and support vector machine classifier for physical activity recognition. The experimental results show that the proposed system provides adequate performance for both purposes, and prove that non-contact passive Doppler radar is a complementary technology to meet the challenges of future healthcare applications.

The use of Wi-Fi signals for human sensing has gained significant interest over the past decade. Such techniques provide affordable and reliable solutions for healthcare-focused events such as vital sign detection, prevention of falls and long-term monitoring of chronic diseases, among others. Currently, there are two major approaches for Wi-Fi sensing: (1) passive Wi-Fi radar (PWR) which uses well established techniques from bistatic radar, and channel state information (CSI) based wireless sensing (SENS) which exploits human-induced variations in the communication channel between a pair of transmitter and receiver. However, there has not been a comprehensive study to understand and compare the differences in terms of effectiveness and limitations in real-world deployment. In this paper, we present the fundamentals of the two systems with associated methodologies and signal processing. A thorough measurement campaign was carried out to evaluate the human activity detection performance of both systems. Experimental results show that SENS system provides better detection performance in a line-of-sight (LoS) condition, whereas PWR system performs better in a non-LoS (NLoS) setting. Furthermore, based on our findings, we recommend that future Wi-Fi sensing applications should leverage the advantages from both PWR and SENS systems.