Self-excited high frequency combustion instability (HFCI) of first-order tangential (1T) mode was observed in a staged-combustion LOX/Kerosene liquid rocket engine numerically. Two different kinds of 1T patterns, standing wave mode and traveling wave mode, were captured in the present work. In the nominal operation condition, the ratio of oxygen-to-fuel (O/F) was 2.5. Propellant was evenly distributed in all injectors and no HFCI occurred. The chamber pressure obtained from the numerical simulation and experiment showed a good agreement, which validated the numerical model. When the mass flow of fuel for two injectors was modified, severe HFCI occurred. The pressure wave node was located at a fixed diameter, showing a 1T standing wave mode. As the O/F was set 4.4 and the propellant distribution was completely uniform, the numerical result yielded a 1T wave node featured a spinning behavior, which was a traveling 1T wave mode. Once the HFCI arose, no matter what standing mode or spinning mode, the pressure and heat release oscillated totally in phase temporally and coupled spatially. The heat release from combustion was fed into the resonant acoustic mode. This was the thermoacoustic coupling process that maintained the HFCI.
The volume of fluid (VOF) model and the adaptive mesh refinement (AMR) method are used to study the spray characteristics of a gas–liquid pintle injector and the effects of mass flow pulsation of liquid on it. A pintle injector is a thrust adjusting device that changes the injection area using movable parts. Pressure pulsation in the supply pipeline is simulated by periodically changing the mass flow rate of the inlet. Spray characteristics with constant and pulsating upstream flows are compared with each other. The effect of frequency and amplitude of upstream liquid flow pulsation on the spray performance was studied. The results reveal that holding the mass flow rate of the upstream liquid flow constant, under the impact of gas flow, the liquid block, the liquid filament, and a large number of small droplets are peeled off from the liquid film. The film breakup position stays relatively fixed, and the spray has a conical shape. However, when the upstream liquid flow is pulsating, the film breakup position changes periodically, and the spray has a “Christmas tree”-shape. The pulsation frequency has little effect on the spray angle. But it strongly determines the droplet size and the spatial distribution of the spray. In addition, the pulsation amplitude can enhance the phenomenon of “Christmas tree.” With the increase in pulsation amplitude, the liquid film at the outlet of the pintle injector appears with a periodic phenomenon of “contraction–expansion.”
Compared to the continuous mode of a high-frequency alternating current (HFAC) source, the burst mode is believed to be capable of controlling flow and combustion while saving discharge energy. Thus, the effect of burst mode on plasma-assisted flame stabilization, which is driven by an HFAC source, is investigated based on a plasma manipulation diffusion flame experiment system. A specially designed injector with a coaxial dielectric barrier discharge configuration is used to generate a methane-air diffusion flame and air plasma. The influence of the actuating parameters of the burst mode on plasma flame stabilization and the discharge power consumption are studied. The results show that the plasma injector has the typical volt–ampere characteristics of dielectric barrier discharge. The discharge clearly exhibits regular unsteady operation characteristics when the source is in burst mode. Two flame stability thresholds are found with increasing discharge voltage. According to the first and second flame stability threshold values and the flame pattern, raising the control frequency and the duty cycle is favorable for flame stabilization. However, for a fixed duty cycle of 50%, because the time scale of the actuator-off duration is longer than that of combustion, when the control frequency is too low, the flame cannot be stabilized even though the applied voltage is very high. For a fixed control frequency of 100 Hz, the flame is also difficult to stabilize when the duty cycle is too small. Mainly due to the unsteady gasdynamic effects of plasma in the burst mode, this approach can achieve the same flame stabilization effect as that of the continuous mode while reducing the energy consumption. The cost-effectiveness ratios of the two optimum actuation schemes are only 6.4% and 10.1%. In addition, the burst mode is better than the continuous mode in avoiding undesirable arc discharge. To better stabilize the flame while maintaining a relatively low cost-effectiveness ratio, actuator setting schemes with high frequency and a small duty cycle should be selected.
Mixing process and flow field structures of liquid jet in high speed crossflow (Mach = 2) in the tandem backward-facing step cavity combustion chamber were investigated numerically. The Eulerian–Lagrangian method coupled with Kelvin–Helmholtz/Rayleigh–Taylor instability breakup model was employed in the simulation. Effects of the position of the backward-facing step and the length of the backward-facing step on droplet mixing in the cavity were studied. The simulation results showed good agreement with experimental data. It was revealed that in high speed crossflow, the jet atomization region can be roughly divided into three regions: the mainstream region, the cavity recirculation region, and the backward-facing step recirculation region. According to the flow mode in the cavity, the cavity recirculation region can be divided into four modes: open cavity (mode I), closed cavity (mode II), open cavity with reattachment shock wave uplift (mode III), and closed cavity with reattachment shock wave uplift (mode IV). The number of droplets entering the cavity is lower in modes I and III compared to modes II and IV, where a greater number of droplets enter the cavity.
Effects of secondary gas injection on flame shape and combustion stability of a premixed swirl methane/air flame were investigated experimentally. Without secondary gas injection, an attached M-shaped flame was observed with pressure oscillations up to a sound pressure level of 68 dB. The flame exhibited significant oscillations due to flame–vortex interactions induced by velocity fluctuations. The secondary methane or air was separately injected into the outer recirculation zone to suppress the flame oscillations at a volume flow rate of 0.5% of the primary flow rates. For lower primary air flow rates (Qair ≤ 60 L/min), both secondary methane and air injections were able to suppress the thermoacoustic instability and performed the sound pressure level reduction of 45 dB. Meanwhile, the flame transformed from an attached unstable M-shaped flame to a detached stable V-shaped flame. The secondary methane or air injection served to stabilize the flame and anchor its spatial heat release distribution by limiting the variation of flame shape in the outer recirculation zone, suppressing thermoacoustic oscillation. For higher primary air flow rates (Qair = 80 L/min), the secondary methane injection could reduce sound pressure levels to noise levels, while secondary air injection could not. The velocity disturbances and heat release fluctuations introduced by secondary methane injection could lead to a transformation in flame shape and achieve the suppression of thermoacoustic oscillation. However, the velocity disturbances induced by secondary air injection were insufficient to stabilize the flame.