A plasma injector element was designed to experimentally study the mechanism of methane-air diffusive flame stabilized by a discharge plasma. The air plasma was generated within the annulus gap of the injector by alternating current dielectric barrier discharge. The discharge voltage, current and photographs were recorded first. Three internal effects of the plasma on combustion were later investigated separately through several diagnostic methods, including optical emission spectrometry (OES), infrared thermography, thermocouple, infrared thermometer, schlieren imaging, photos and CH ^* chemiluminescence. Finally, the return on investment (ROI) was calculated. The results showed that a large number of filamentary micro discharge paths occur within the discharge gap. These discharge paths rotate anticlockwise at high speed and act as a virtual ‘fan’ to induce the flow jet. The velocity of the induced jet increases with increasing discharge voltage. The original jet expansion angle is enlarged by the radial velocity component of the induced jet, resulting in the mixing enhancement of the air and methane. The plasma rotational temperature (the first negative system ) obtained from OES is close to the discharge gas temperature measured by infrared thermography, indicating that the discharge gas temperature can be approximately represented by the rotational temperature. According to the measured temperature of the injector and the jet, the impact of the thermal effect of the plasma on flame stabilization is negligible. Due to the plasma, the height of the flame center and its representative length are generally reduced as the voltage rises, and the methane-air mixture becomes ignitable, and a stable flame can be reached under the conditions in which direct ignition fails. The combustion is enhanced with increasing heat release rate of the flame by the plasma. This finding revealed that the ROI of plasma-assisted flame stabilization is lower under a higher flowrate and a larger equivalence ratio for unstable flame situations.

The process of dielectric barrier discharge (DBD) plasma flow-separation control on screw propeller is numerically simulated based on the unsteady compressible Navier-Stokes equations loosely with DBD-plasma body force aerodynamic actuation mechanism. The effect and the mechanism of plasma flow control to enhance the propeller aerodynamic characteristics are discussed. The results show that the propeller aerodynamic characteristics will decrease as the altitude increase without plasma flow control, but it will first increase and then decrease as the altitude increases with plasma flow control. The effect of DBD-plasma flow control on the distribution of pressure is small at ground condition, and the difference of pressure distribution between general propeller and plasma efficiency-enhance propeller will be increased as the altitude increases. The effect of DBD-plasma flow-separation control will increase as the altitude increases. Mainly, the mechanism of the plasma flow control to enhance the propeller aerodynamic is obtained as follows. The flow separation on the propeller blade surface could be effectually controlled by DBD-plasma aerodynamic actuation, thereby increasing the efficiency of the propeller. The pressure of the windward surface of the blade will decrease by the plasma body force, which will increase the thrust of the propeller.

Compared to the continuous mode of a high-frequency alternating current (HFAC) source, the burst mode is believed to be capable of controlling flow and combustion while saving discharge energy. Thus, the effect of burst mode on plasma-assisted flame stabilization, which is driven by an HFAC source, is investigated based on a plasma manipulation diffusion flame experiment system. A specially designed injector with a coaxial dielectric barrier discharge configuration is used to generate a methane-air diffusion flame and air plasma. The influence of the actuating parameters of the burst mode on plasma flame stabilization and the discharge power consumption are studied. The results show that the plasma injector has the typical volt–ampere characteristics of dielectric barrier discharge. The discharge clearly exhibits regular unsteady operation characteristics when the source is in burst mode. Two flame stability thresholds are found with increasing discharge voltage. According to the first and second flame stability threshold values and the flame pattern, raising the control frequency and the duty cycle is favorable for flame stabilization. However, for a fixed duty cycle of 50%, because the time scale of the actuator-off duration is longer than that of combustion, when the control frequency is too low, the flame cannot be stabilized even though the applied voltage is very high. For a fixed control frequency of 100 Hz, the flame is also difficult to stabilize when the duty cycle is too small. Mainly due to the unsteady gasdynamic effects of plasma in the burst mode, this approach can achieve the same flame stabilization effect as that of the continuous mode while reducing the energy consumption. The cost-effectiveness ratios of the two optimum actuation schemes are only 6.4% and 10.1%. In addition, the burst mode is better than the continuous mode in avoiding undesirable arc discharge. To better stabilize the flame while maintaining a relatively low cost-effectiveness ratio, actuator setting schemes with high frequency and a small duty cycle should be selected.