A curved nanosecond-pulsed dielectric barrier discharge actuator is proposed to fit the flexibly complex surface shape of air vehicles. Streamer evolution and aerodynamic perturbations driven by a single-pulse voltage applied on the anode, where the pulse width is 35 ns and the peak voltage is 14 kV, are numerically studied. Continuity equations that consider 15 species and 34 reactions are solved based on the drift–diffusion approximation. The electron temperature is obtained using the local mean energy approximation method. Discharge characteristics during the voltage-rise, plateau and decay stages are discussed, respectively. The streamer is initiated at 2.2 ns. The maximum electric field is progressively located at the head of the streamer, between the electrodes and in the dielectric layer during the three voltage stages, while the maximum value of electron density is settled at the downstream tip of the driven anode. The electron number density at the streamer head increases at the voltage-rise stage, keeps constant during the voltage-plateau stage, decreases at the beginning of the voltage-decay stage and then increases due to the quenching effect of the excited species. Compared with the discharge on a flat surface, the initial discharge propagation velocity is smaller, while it decreases more slowly during the entire applied voltage. The simulated deposited energy matches the analytical solution well. Aerodynamic perturbations are investigated by solving the compressible Navier–Stokes equations. The ambient air is rapidly heated to the maximum temperature of 1883 K within 0.04 μs. The temperature rise remains greater than 1000 K for 0.32 μs and greater than 500 K for 21.6 μs. A ‘semiring-like’ compression wave is formed from the discharge region; the propagation speed decreases as it propagates away from the wall and then converges to 345 m s−1 at 13 μs. High-speed flows are rapidly induced at the beginning, and two vortexes are formed successively due to the interaction between the flow induced by the actuator and the backflow induced by the compression wave.
In this paper, the multicomponent lattice Boltzmann flux solver (LBFS) is developed for simulation of two-dimensional compressible viscous reacting flows. This work is based on the existing LBFS for simulation of single-component compressible flows. The present solver applies the finite volume method to discretize the multicomponent Navier-Stokes equations and evaluates the numerical flux at the cell interface by local solution of the lattice Boltzmann equation. To evaluate numerical flux, the original non-free parameter D1Q4 model in the existing LBFS is extended to the multicomponent counterpart in which the total density at the cell interface is computed directly by summing the density distribution functions, and the densities of different species are calculated from the mass fractions at the left and right sides of cell interface. The internal energy is evaluated from the enthalpy which considers the different physical properties of the species, and the temperature at the cell interface is obtained by Newton iteration. In addition, an improved switch function which takes into account the reacting effects and aspect ratio of the grid is introduced to control the numerical dissipation. Several benchmark problems are simulated to validate the present multicomponent LBFS. It is shown that the present solver is carbuncle-free for the unfavorable aspect ratio grid in the test cases here and has a satisfied performance for simulation of multicomponent compressible viscous reacting flows.
The overall performance of a scramjet inlet will decline while entering off-design mode. Active flow control using nanosecond surface dielectric barrier discharge (NS-SDBD) can be a novel solution to such inlet–unstart problems. NS-SDBD actuators are deployed on the surface of the internal compression section, controlling the shock waves and the separation area. Numerical simulations of hypersonic flows are carried out using the compressible Reynolds average Navier–Stokes equation (RANS), along with the plasma phenomenological model which is added in as the energy source term. Flow structures and the evolution of performance parameters are analyzed. Results show that NS-SDBD actuators are able to increase the static pressure behind the cowl shock, boosting the downstream total pressure. The compression effect becomes stronger while raising the frequency or shortening the spacing between the actuators. Under the inlet–unstart conditions, the compression wave generated by the actuator pushes the reattachment point forward, making the separation bubble longer in length and shorter in height, which reduces the strength of the separation shock. The results provide a numerical basis for the state control of a hypersonic inlet.
The efficiency of supersonic combustion is largely dependent on inlet and injection parameters. Additional energy input is required in some off-design conditions, and nanosecond discharge actuation can be a solution. In the present study, a phenomenological model of a nanosecond-pulsed surface dielectric barrier discharge (NS-SDBD) actuator was developed to analyze the combustion enhancement effect for a supersonic combustor with transverse H2 injection. A seven-reaction H2–air combustion model was adopted for the numerical simulation. Dynamic mode decomposition (DMD) was employed to acquire temperature perturbation in spatial and temporal domains. The results show that the actuator provides additional temperature-increment and species transportation through compression waves. The combustion enhancement effect is mainly attributed to the flow perturbation in the shear layer, which promotes the turbulent diffusion of fuel. Given the same power input, the combustion efficiency at the shockwave reflection point is increased by 17.5%, and the flame height is increased by 15.4% at its maximum.
10 March 2021 in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
The reaction control system with multiple lateral jets shows great advantages in agility and maneuverability for supersonic air vehicles. Interactions among sonic jet plumes, X-shape fins, and supersonic crossflow at Mach 4.5 and Reynolds number 3.8 × 107 are numerically studied considering different number of jets for a large slenderness ratio missile with 7 jet exits. Three-dimensional Reynolds-averaged Navier–Stokes equations closed by Spalart–Allmaras turbulence model for the structured grid are validated and solved. The overall force and moment amplification factors of configurations with and without fins are analyzed and compared. Moreover, the force and moment amplification factors on fins and ratio of force and moment on fins are proposed and discussed to measure the jet effectiveness contributed from fins. The number of jet plumes is under consideration for all cases. Results show that the increment of effectiveness decreases as the number of jets increases for the finned configuration. Fins can significantly improve the jet effectiveness with more than 70% force and 50% moment increment, which shows great advantages to the jet effectiveness as well as the overall aerodynamic performance.