The article details experimental work to evaluate tool wear, cutting forces/torque and associated hole quality/accuracy following single-shot drilling of twin layer CFRP/AA7010 stacks. A full factorial experiment was initially planned involving variation in cutting speed (60 and 120 m/min), feed rate (0.15 and 0.30 mm/rev) and drill tip geometry (double cone and flat point drills). While flank wear for the flat point drills did not exceed 40 µm even after 120 holes irrespective of operating conditions, the double cone geometry suffered catastrophic failure after only four holes at the lowest parameter combination. Therefore, the remaining tests involving the double cone drill at higher operating parameters were subsequently halted. Feed rate had a significant influence on torque in both the CFRP and Al layers, although thrust force and torque generally remained stable over the test duration. Hole diameter was typically up to 34 µm above the nominal value of 6.38 mm with corresponding out of roundness of <60 µm. Burrs were prevalent at hole exit in all tests, with an average height of ∼120 µm when drilling at the highest cutting speed–feed rate parameter combination. Similarly, the delamination factor at hole entry increased by up to 23% when operating at the higher feed rate level.
Purpose: The purpose of this study is to develop a manufacturing technology using hybrid selective laser melting/hot isostatic pressing (SLM/HIP) process to produce full density net-shape components more rapidly and at lower cost than processing by SLM alone. Design/methodology/approach: Ti-6Al-4V powder was encapsulated in situ by the production of as-SLMed shell prior to the HIP process. After HIPping, the SLM shell is an integral part of the final component. Finite element (FE) modelling based on pure plasticity theory of porous metal coupled with an iterative procedure has been adopted to simulate HIPping of the encapsulated Ti-6Al-4V powder and SLMed shell. Two demonstrator parts have been modelled, designed, produced and experimentally validated. Geometrical analysis and microstructural characterisation have been carried out to demonstrate the efficiency of the process. Findings: The FE model is in agreement with the measured data obtained and confirms that the design of the shell affects the resulting deformed parts. In addition, the scanning electron microscope (SEM) and Electron backscatter diffraction EBSD (EBSD) of the interior and exterior parts reveal a considerably different grain structure and crystallographic orientation with a good bonding between the SLMed shell and HIPped powder. Originality/value: An approach to improve SLM productivity by combining it with HIP is developed to further innovate the advanced manufacturing field. The possibility of the hybrid SLS/HIP supported by FEA simulation as a net shape manufacturing process for fabrication of high performance parts has been demonstrated.
27 September 2016 in SAE International Journal of Aerospace
Despite the increasing use of carbon fibre reinforced plastic (CFRP) composites, titanium and aluminium alloys still constitute a significant proportion of modern civil aircraft structures, which are primarily assembled via mechanical joining techniques. Drilling of fastening holes is therefore a critical operation, which has to meet stringent geometric tolerance and integrity criteria. The paper details the development of a three-dimensional (3D) finite element (FE) model for drilling aerospace grade aluminium (AA7010-T7451 and AA2024-T351) and titanium (Ti-6Al-4V) alloys. The FE simulation employed a Coupled Eulerian Lagrangian (CEL) technique. The cutting tool was modelled according to a Lagrangian formulation in which the mesh follows the material displacement while the workpiece was represented by a non-translating and material deformation independent Eulerian mesh. The performance of the CEL based simulation was also benchmarked against an equivalent pure Lagrangian model (both tool and workpiece mesh deforms with the material). The geometry of commercially supplied twin-fluted twist drills utilised in experimental validation trials were imported into the model. Cutting speed (m/min)/ feed rate (mm/rev) combinations were 50/0.08 and 150/0.24 for the aluminium alloys while 10/0.07 and 30/0.21 were used when drilling Ti-6Al-4V. Predicted cutting forces from the CEL model were within 3-14% of the experimentally measured values while the simulated entrance and exit burr height deviated by 6-17.5% and 9-16% respectively, compared to experimental results. Additionally, the model indicated that hole surface residual stresses were typically compressive, with values of up to -344 and -711 MPa for aluminium and titanium workpieces respectively.