Da Zong

Mr. Da Zong

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 November 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
DKDing Kewei
Ding Kewei
DZDa Zong
Da Zong
YLYunlin Liu
Yunlin Liu
书何书林 何书林
书林 何书林
WSWanyu Shen
Wanyu Shen
In this paper, a new ALC panel connector was proposed. It has a good engineering economy and high fault tolerance. A quasistatic loading experiment was carried out to verify the feasibility of the external ALC panel steel frame under seismic loading. The test phenomena, hysteretic curve, skeleton curve, stiffness degradation, and energy dissipation of two sets of full-scale specimens were analyzed and discussed. Moreover, the simulation of pendulous Z-panel connectors with different thicknesses was carried out using ABAQUS software. The comparison reveals that the semi-rigid connection has a full hysteresis curve, good energy dissipation capacity, and a 15% increase in peak load capacity. Finally, similar results for different thicknesses in the use of pendulous Z-panel connectors reveal that using the 6 mm connector may be the most economical solution for engineering.

8 December 2023 in Advances in Civil Engineering
Verified
Journal Article
Open access
PDF file
PXPengfei Xu
Pengfei Xu
LWLi Wang
Li Wang
JCJian Chen
Jian Chen
MLMing Li
Ming Li
RGRui Guo
Rui Guo
DZDa Zong
Da Zong
Box culvert structure was an essential part of modern infrastructure. Due to the advantages of low pollution and convenient construction, the prefabricated box culvert (PBC) has been gradually utilized in engineering. However, the investigations on load bearing capacity of PBC in different reinforcement forms with same reinforcement ratios were still lack. In the present research, one PBC specimen was tested and discussed by the finite-element analysis (FEA) on load bearing capacity under four-point bending. The load bearing capacity of another three PBCs in different reinforcement forms with the same reinforcement ratios was discussed by the FEA. Results of experimental and numerical investigations showed that: (1) a number of flexural cracks were observed in the midspan bottom of upper slab of PBC, and finally shear failure was observed in bending–shear zone of upper slab of PBC; (2) the number of concrete cracking, plastic deformation of PBC, and stress of rebars reduced by increasing the area of tensile rebars in PBC with reducing the area of compressive rebars under same reinforcement ratios; (3) the ductility and load bearing capacity of PBC increased by increasing the area of tensile rebars with reducing the area of compressive rebars.

25 November 2022 in Buildings
Verified
Journal Article
Open access
PDF file
DKDing Kewei
Ding Kewei
DKding kewei
ding kewei
书何书林 何书林
书林 何书林
DZDa Zong
Da Zong
This paper presents a new type of connector which is used in prefabricated structures for attaching the autoclaved lightweight concrete panels to the steel frame. The new type of connector is composed of an L-node plate and a Z-node plate and is termed as the “pendulous Z-plate connector”. For examining the seismic behavior of the new connector, two full-scale steel frames with cladding panel walls, in which the ALC panels are connected to the steel frame by both classical and new connectors, were tested under quasi-static loading. The failure mode, hysteresis performance, energy dissipation, and stiffness degradation of the structures were measured and compared. The experimental results indicate that the new connector facilitates a better structural performance of cladding panel walls than the classical connector in terms of the coordinating deformation, the energy dissipation, and the load-carrying capacity at the yielding and the ultimate stages. In addition, for in-depth analysis of the failure mechanism, the finite element modeling was conducted and validated based on the comparison with the experimental results. Further parametric studies are carried out to find out the effect of bolt grades on the structure.