书林 何书林

Mr. 书林 何书林

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 November 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
DKDing Kewei
Ding Kewei
DZDa Zong
Da Zong
YLYunlin Liu
Yunlin Liu
书何书林 何书林
书林 何书林
WSWanyu Shen
Wanyu Shen
In this paper, a new ALC panel connector was proposed. It has a good engineering economy and high fault tolerance. A quasistatic loading experiment was carried out to verify the feasibility of the external ALC panel steel frame under seismic loading. The test phenomena, hysteretic curve, skeleton curve, stiffness degradation, and energy dissipation of two sets of full-scale specimens were analyzed and discussed. Moreover, the simulation of pendulous Z-panel connectors with different thicknesses was carried out using ABAQUS software. The comparison reveals that the semi-rigid connection has a full hysteresis curve, good energy dissipation capacity, and a 15% increase in peak load capacity. Finally, similar results for different thicknesses in the use of pendulous Z-panel connectors reveal that using the 6 mm connector may be the most economical solution for engineering.

17 March 2022 in Buildings
Verified
Journal Article
Open access
PDF file
CZChikun Zhang
Chikun Zhang
DKDing Kewei
Ding Kewei
书何书林 何书林
书林 何书林
This paper proposes new prefabricated autoclaved lightweight concrete (ALC) connectors which allow limited sliding. The seismic performance of the proposed connectors and a traditional connector (L-hooked bolt) were investigated in depth. Three specimens of full-scale steel frames with ALC panel and connectors were subjected to horizontal low-cyclic loading. The failure modes, hysteretic behavior, strength and deterioration of stiffness and energy-dissipating performance of all specimens were analyzed and discussed. The experimental results indicated that the frames of the new connectors were more reliable than the traditional connector. The energy-dissipating capacity of the specimen frames with new connectors increased by 23.0% and 24.4%, and deterioration of stiffness increased by 10.6% and 13.0%. The new ALC panel connectors not only increased elastic stiffness in the early stage, but also provided some stiffness in the elastoplastic and plastic stages. Using relevant construction measures, the frames with new connectors displayed good cooperative behavior and safety reliability. To summarize, the new ALC connectors tested showed excellent performance in resisting seismic loading and had good assembly efficiency and could provide a basis for the development and application of a new type of ALC steel frame connector.

8 December 2022 in Materials
Verified
Journal Article
Open access
PDF file
JCJianhua Cui
Jianhua Cui
书何书林 何书林
书林 何书林
DKDing Kewei
Ding Kewei
ZYZhang Yu
Zhang Yu
DKding kewei
ding kewei
In this paper, a new slip-type crossing connector is proposed for autoclaved aerated concrete (ALC) panels with steel frames, and the proposed connector is also studied deeply in terms of seismic performance. The research included pseudo-static tests and finite element simulations. First, the seismic performance of slip-type crossing connectors and standard L-hooked bolts was studied comparatively, including the stability, bearing capacity, stiffness, energy dissipation, and hysteresis performance. ABAQUS 2020 software was used to establish finite element models, and the results of the experiments were verified with simulations on the basis. According to the simulations, a parameter analysis of connector optimization was carried out. The effects of connector thickness and connector plate length on the seismic performance were further investigated. From the experimental and simulation results, the slip-type crossing connector has excellent performance and good assembly efficiency, it can improve the deficiencies of the existing connectors. The comparison demonstrated that the slip-type crossing connector has a complete hysteresis curve, a high energy dissipation capacity, and a 9.7% increase in bearing capacity. The appropriate reduction in connector thickness and plate length can ensure superior seismic performance while saving resources. The finite analysis method can guide the design and implementation of new external ALC panel connectors.

25 November 2022 in Buildings
Verified
Journal Article
Open access
PDF file
DKDing Kewei
Ding Kewei
DKding kewei
ding kewei
书何书林 何书林
书林 何书林
DZDa Zong
Da Zong
This paper presents a new type of connector which is used in prefabricated structures for attaching the autoclaved lightweight concrete panels to the steel frame. The new type of connector is composed of an L-node plate and a Z-node plate and is termed as the “pendulous Z-plate connector”. For examining the seismic behavior of the new connector, two full-scale steel frames with cladding panel walls, in which the ALC panels are connected to the steel frame by both classical and new connectors, were tested under quasi-static loading. The failure mode, hysteresis performance, energy dissipation, and stiffness degradation of the structures were measured and compared. The experimental results indicate that the new connector facilitates a better structural performance of cladding panel walls than the classical connector in terms of the coordinating deformation, the energy dissipation, and the load-carrying capacity at the yielding and the ultimate stages. In addition, for in-depth analysis of the failure mechanism, the finite element modeling was conducted and validated based on the comparison with the experimental results. Further parametric studies are carried out to find out the effect of bolt grades on the structure.

22 February 2022 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
PDF file
DKDing Kewei
Ding Kewei
CZChikun Zhang
Chikun Zhang
书何书林 何书林
书林 何书林
YLYun-Lin Liu
Yun-Lin Liu
This paper proposes a new flexible connector for the autoclaved lightweight concrete (ALC) panel with the steel beam. It is a universal upper and lower crossing connector, with load-bearing and limitation holes; then, the seismic capacity of this connector is investigated in the simulations and full-scale tests. Firstly, the finite element simulations of the new connector and traditional connector (L-hooked bolt) were made by ABAQUS, which proved the reliability of the new connector by comparing them in low-cyclic loading. Secondly, in order to analyze the phenomenon and data of the two connectors which are in the same test conditions of simulation, the full-scale tests of the steel frame were conducted. The damage of the ALC panel at different connectors and at different test load displacements is described in detail. The contribution of the connectors to the steel frame and the ALC panel is investigated in depth during the elastic, elastoplastic, and plastic stages of the steel frames. The test result is similar to the simulation result roughly, in which the new connector has better seismic capability. In minor earthquakes, the ALC panel frame with the new connector has better synergistic capacity of panels, while in large earthquakes, it can provide certain stiffness to the structure. Compared with the L-hooked bolt, the maximum bearing capacity of the structure with the new connector increases by 5.2%, and the yield displacement delays by 27.5%, which results in the increase of ductility by 9.8%. In terms of energy consumption capacity, the equivalent damping factor of the new connector increases by 10.2% and 35.3% at the yield and ultimate state, respectively. The FEM simulation results can represent the actual test results well. To summarize, the new ALC panel connector in this paper has excellent seismic capacity and good synergistic, which can provide a reference for the development and application of new types of the ALC connector.