Microplastic contamination is a growing threat to marine and freshwater ecosystems, agricultural production, groundwater, plant growth and even human and animal health. Disintegration of plastic products due to mainly biochemical or physical activities leads to the formation and existence of microplastics in significant amounts, not only in marine and freshwater environments but also in soils. There are several valuable studies on microplastics in soils, which have typically focused on environmental, chemical, agricultural and health aspects. However, there is also a need for the geotechnical engineering perspective on microplastic contamination in soils. In this review paper, first, degradation, existence and persistence of microplastics in soils are assessed by considering various studies. Then, the potential role of solid waste disposal facilities as a source for microplastics is discussed by considering their geotechnical design and addressing the risk for the migration of microplastics from landfills to soils and other environments. Even though landfills are considered as one of the main geotechnical structures that contribute to the formation of considerably high amounts of microplastics and their contamination in soils, some other geotechnical engineering applications (i.e., soil improvement with tirechips, forming engineering fills with dredged sediments, soil improvement with synthetic polymer-based fibers, polystyrene based lightweight fill applications), as potential local source for microplastics, are also mentioned. Finally, the importance of geotechnical engineering as a mitigation tool for microplastics is emphasized and several important research topics involving geotechnical engineering are suggested.
1 December 2021 in Soil Dynamics and Earthquake Engineering
Liquefaction of clean and silty sands remains to be an important problem during earthquakes. Even though many factors are known to influence liquefaction behavior, the influence of density index parameter and fines content (FC) are among the most important parameters. In this study, the effect of relative density (Dr) on liquefaction behavior of clean and silty sands was investigated by cyclic direct simple shear tests on two different silty sands at various FC. Several different relationships affected from Dr are revisited or investigated including number of cycles to liquefaction (NL) and cyclic resistance ratio (CRR). It was found that liquefaction resistance-fines content-relative density relationship is much more complex than previously thought. This is because CRR-Dr lines of clean and/or silty sands may cross each other at specific relative densities, which may cause the liquefaction resistance of a clean sand to be either smaller, equal or greater than the liquefaction resistance of a silty sand with the same base sand dependent on the magnitude of relative density. The mentioned behavior is also confirmed on different clean and silty sands tested in literature.
The common assumption in geotechnical engineering research and practice has been that nonplastic silts behave sand-like, whereas, as silts become more plastic, they start to behave clay-like. To date, there are practically no studies focusing solely on various nonplastic silts and their monotonic response, perhaps because of the solid belief that nonplastic silts behave sand-like in all aspects. A series of constant volume direct simple shear tests were conducted on three different nonplastic silts. Because the specimens were reconstituted to have loose grain structures, volumetrically contractive tendency was observed for all the silts with relatively small effective stress friction angles. It was observed that Ko compression lines and critical state lines are parallel to each other for all three silts, which is considered to be a clay-like behavior in literature. It was shown that undrained shear strengths can be normalized with the effective vertical consolidation stress, which is also considered to be a clay-like behavior in literature. Normalized values are compared with the ones obtained for plastic silts compiled from previous studies. Normalized undrained shear strength values for plastic silts in literature were seen to be typically greater. Possible reasons such as density effect and strength anisotropy were discussed.
Silty sands are among the soil types that are prone to liquefaction when subjected to static or dynamic undrained loading. Today, it is widely accepted that clean sands and silty sands react differently in terms of liquefaction behavior. With this observation, factors influencing fines' role on such a difference have been investigated by various researchers. Some of those factors such as laboratory specimen preparation method and confining stress are relatively well understood. However, some others such as fines content (FC) are still debated and being investigated. More explicitly, there is not a widely accepted consensus on whether increasing fines content increases or decreases the liquefaction resistance of silty sands, even with the same comparison basis (i.e. loosest possible density after deposition, same void ratio, same relative density etc.). Recently, relative size of silt grains to the sand grains is also found to be another factor influencing the fines' role on liquefaction behavior of silty sands. In this paper, some of the research in literature regarding liquefaction of silty sands is re-visited and various factors influencing the fines' role on liquefaction behavior are summarized.