Xianping Wang

Prof. Xianping Wang


Research Focus & Metrics

Academic Career Length

34Years (1993-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 November 2015 in Scientific Reports
Verified
Journal Article
Open access
PDF file
ZXZ. M. Xie
Z. M. Xie
RLRui Liu
Rui Liu
SMS. Miao
S. Miao
XYX. D. Yang
X. D. Yang
TZTao Zhang
Tao Zhang
XLX. Liu
X. Liu
The refractory tungsten alloys with high ductility/strength/plasticity are highly desirable for a wide range of critical applications. Here we report an interface design strategy that achieves 8.5 mm thick W-0.5 wt. %ZrC alloy plates with a flexural strength of 2.5 GPa and a strain of 3% at room temperature (RT) and ductile-to-brittle transition temperature of about 100 °C. The tensile strength is about 991 MPa at RT and 582 MPa at 500 °C, as well as total elongation is about 1.1% at RT and as large as 41% at 500 °C, respectively. In addition, the W-ZrC alloy plate can sustain 3.3 MJ/m2 thermal load without any cracks. This processing route offers the special coherent interfaces of grain/phase boundaries (GB/PBs) and the diminishing O impurity at GBs, which significantly strengthens GB/PBs and thereby enhances the ductility/strength/plasticity of W alloy. The design thought can be used in the future to prepare new alloys with higher ductility/strength.

18 August 2009 in Materials
Verified
Journal Article
Open access
PDF file
HLHui Lu
Hui Lu
XWXianping Wang
Xianping Wang
TZTao Zhang
Tao Zhang
ZCZhijun Cheng
Zhijun Cheng
QFQianfeng Fang
Qianfeng Fang
Nowadays it is commonly considered that high damping materials which have both the good mechanical properties as structural materials and the high damping capacity for vibration damping are the most direct vibration damping solution. In metals and alloys however, exhibiting simultaneously high damping capacity and good mechanical properties has been noted to be normally incompatible because the microscopic mechanisms responsible for internal friction (namely damping capacity) are dependent upon the parameters that control mechanical strength. To achieve a compromise, one of the most important methods is to develop two-phase composites, in which each phase plays a specific role: damping or mechanical strength. In this review, we have summarized the development of the design concept of high damping composite materials and the investigation of their fabrication and properties, including mechanical and damping properties, and suggested a new design concept of high damping composite materials where the hard ceramic additives exhibit high damping capacity at room temperature owing to the stress-induced reorientation of high density point defects in the ceramic phases and the high damping capacity of the composite comes mainly from the ceramic phases.

1 October 2019 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
RDRongfa Ding
Rongfa Ding
HWHui Wang
Hui Wang
YJYan Jiang
Yan Jiang
RLRui Liu
Rui Liu
KJKe Jing
Ke Jing
CLChangsong Liu
Changsong Liu

1 September 2020 in Acta Materialia
Verified
Journal Article
Closed access
RGRui Gao
Rui Gao
MJMiaomiao Jin
Miaomiao Jin
FHFei Han
Fei Han
BWBaoming Wang
Baoming Wang
XWXianping Wang
Xianping Wang
JLJu Li
Ju Li

1 June 2018 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
MSMeng Sun
Meng Sun
XWXianping Wang
Xianping Wang
LWLe Wang
Le Wang
HWHui Wang
Hui Wang
WJWeibin Jiang
Weibin Jiang
CLChangsong Liu
Changsong Liu

17 January 2017 in Scientific Reports
Verified
Journal Article
Open access
PDF file
LZL. F. Zeng
L. F. Zeng
RGR. Gao
R. Gao
ZXZ. M. Xie
Z. M. Xie
SMS. Miao
S. Miao
QFQianfeng Fang
Qianfeng Fang
CLC. S. Liu
C. S. Liu
Traditional nanostructured metals are inherently comprised of a high density of high-energy interfaces that make this class of materials not stable in extreme conditions. Therefore, high performance bulk nanostructured metals containing stable interfaces are highly desirable for extreme environments applications. Here, we reported an attractive bulk Cu/V nanolamellar composite that was successfully developed by integrating interface engineering and severe plastic deformation techniques. The layered morphology and ordered Cu/V interfaces remained stable with respect to continued rolling (total strain exceeding 12). Most importantly, for layer thickness of 25 nm, this bulk Cu/V nanocomposite simultaneously achieves high strength (hardness of 3.68 GPa) and outstanding thermal stability (up to 700 °C), which are quite difficult to realize simultaneously in traditional nanostructured materials. Such extraordinary property in our Cu/V nanocomposite is achieved via an extreme rolling process that creates extremely high density of stable Cu/V heterophase interfaces and low density of unstable grain boundaries. In addition, high temperature annealing result illustrates that Rayleigh instability is the dominant mechanism driving the onset of thermal instability after exposure to 800 °C.