This article proposes an automatic T-branch travel method of an articulated wheeled in-pipe inspection robot, AIRo-5.2, using its joint angle response to environmental changes. The robot joints are composed of two passive elastic joints with torsional springs and a single active joint using a polyurethane-based series elastic actuator (SEA). By switching from torque control to angle control of this SEA, the AIRo-5.2 can pass through vertical T-branches. However, the timing needed to switch them has not yet been defined, and thus it was necessary to train the operators. Therefore, a method that uses the middle joint angle change was proposed for automatic T-branch travel. To elucidate the phenomenon of this angle change and to determine the effects of a robot's mechanical parameters, a partial dynamic model was constructed when only the head link contact was released at a T-branch. Finally, the travel performance of our developed in-pipe robot was tested on 10 types of T-branches with different gravity directions. From the experiments, although the probability of completing the course was not 100% in all cases, the effectiveness of our proposed principle and algorithm for automatic T-branch travel was confirmed.
24 January 2018 in IEEE Robotics and Automation Letters
This paper proposes an N-link snake robot with parallel elastic actuators (PEA) and a stiffness property that reduces the energy consumption during fast movement. Each PEA couples the actuator output to a spring element, enhancing the periodic gait as demonstrated in previous studies of walking robots. The PEA can mimic each joint of a typical snake robot, which is also controlled by sinusoidal periodic signals. If the actuator output is synchronized with the resonance frequency of the spring, the PEA can greatly reduce the actuator torque and power. Therefore, the present paper proposes PEAs to reduce the energy consumption of N-link snake robots. After analyzing the robot dynamics, we explain how the torque of each joint is minimized. The energy consumption is evaluated by measuring the motor current in experimental tests. During fast movement of the robot, the PEA reduced the current consumption by 72%.
15 January 2021 in IEEE/ASME Transactions on Mechatronics
The design methodology of a plate-springed parallel elastic actuator (PSPEA) for the efficient movement of planar snake robots is presented. The stiffness, which refers to the relationship between the resilience moment and the joint angle, of the plate spring was first designed using a rigid body spring model. The modeled stiffness was then verified via a simple test rig. Combinations of spring stiffnesses that minimize the energy consumption of each joint at different velocities were obtained using dynamic simulation. Experiments using a planar six-link PSPEA-based snake robot were performed via sensors installed in the servomotors to measure torque and speed, and a motion-tracking system was utilized to measure the moving distance. True efficiency was evaluated using the cost of transport criterion, which was later compared with the dynamic simulation results. Despite its compact design, it was observed that the proposed PSPEA improved the energy efficiency of the snake robot by a maximum of approximately 50%.
This paper proposes an underactuated grippers mechanism that grasps and pulls in different types of objects. These two movements are generated by only a single actuator while two independent actuators are used in conventional grippers. To demonstrate this principle, we have developed two kinds of gripper by different driving systems: one is driven by a DC motor with planetary gear reducers and another is driven by pneumatic actuators with branch tubes as a differential. Each pulling-in mechanism in the former one and the latter one is achieved by a belt-driven finger surface and a linear slider with an air cylinder, respectively. The motor-driven gripper with planetary gear reducers can pull-up the object after grasping. However, the object tends to fall when placing because it opens the finger before pushing out the object during the reversed movement. In addition, the closing speed and the picking-up speed of the fingers are slow due to the high reduction gear. To solve these drawbacks, a new pneumatic gripper by combining three valves, a speed control valve, a relief valve, and non-return valves, is proposed. The proposed pneumatic gripper is superior in the sense that it can perform pulling-up after grasping the object and opening the fingers after pushing-out the object. In the present paper, a design methodology of the different underactuated grippers that can not only grasp but also pull up objects is discussed. Then, to examine the performance of the grippers, experiments were conducted using various objects with different rigidity, shapes, size, and mass, which may be potentially available in real applications.
Conventional multilink articulated in-pipe inspection robots with elongated zig-zag structures are highly adaptive to a small diameter pipe. However, as more modules are connected, the longer the length of the robot becomes, it becomes more difficult to pass through complex-shaped pipes. We previously developed a robot that consists of minimized two-linked structures and realizes propulsive and rolling movements using two standard actuators through a simple miter-gear differential mechanism. Although less actuated design enables a short-length structure of the robot, a transformation method is necessary to change the robot's posture to switch both of the two movements. Thus, in this paper, we introduce a method of driving the underactuated roll-pitch joints through a speed difference between two motors. To adjust the multiple outputs distribution of our underactuated mechanism, many movements that can be generated by controlling the actuators' rotational directions and speeds in the links are described analytically. Among them, the effectiveness of three functional movements is verified experimentally. In addition, trials of the proposed robot in the out-of-plane double elbow will be conducted to demonstrate that the proposed V-shaped structure could pass through a 4-inch out-of-plane double elbow where the existing wheeled and crawler in-pipe robots cannot. GRAPHICAL ABSTRACT
This paper presents a V‐shaped gas pipeline inspection robot which achieves high roll rotation performance, out‐of‐plane double elbow travel performance, and inverted siphon adaptability at high speed without requiring complicated manual operation. The principle for traveling through the out‐of‐plane double elbow was theoretically demonstrated and proven experimentally. The pitch angle of the robot's spiral motion, which is derived from the relationship between the roll angle of the spherical wheel and the angle of the V‐shaped joint, was also both theoretically and experimentally verified. Finally, field tests were conducted not only indoors but also outdoors on 8‐in steel pipes, and the robot successfully adapted to the out‐of‐plane double elbows, inverted siphons, and even buried pipes that were more than 20 years old. The robot even traveled up to 40 m without any problems, and returned safely after inspection and exploration.