By using an independent self-assembly process that is occasionally controlled by evaporation, cellulose nanocrystals (CNCs) may create films (pure or in conjunction with other materials) that have iridescent structural colors. The self-forming chiral nematic structures and environmental safety of a new class of photonic liquid crystals (LCs), referred to as CNCs and CNC-embedded materials, make them simple to make and treat. The structure of the matrix interacts with light to give structural coloring, as opposed to other dye pigments, which interact with light by adsorption and reflection. Understanding how CNC self-assembly constructs structures is vital in several fields, including physics, science, and engineering. To constructure this review, the colloidal characteristics of CNC particles and their behavior during the formation of liquid crystals and gelling were studied. Then, some of the recognized applications for these naturally occurring nanoparticles were summarized. Different factors were considered, including the CNC aspect ratio, surface chemistry, concentration, the amount of time needed to produce an anisotropic phase, and the addition of additional substances to the suspension medium. The effects of alignment and the drying process conditions on structural changes are also covered. The focus of this study however is on the optical properties of the films as well as the impact of the aforementioned factors on the final transparency, iridescent colors, and versus the overall response of these bioinspired photonic materials. Control of the examined factors was found to be necessary to produce reliable materials for optoelectronics, intelligent inks and papers, transparent flexible support for electronics, and decorative coatings and films.
In this work, the nonlinear rheological properties of kaolinite suspensions as a model fluid were studied. Three kaolinites with different average particle, aspect ratio and asperity were used to gain a deeper understanding of the effects of particle's geometry on yielding, rheology, and apparent slip velocity over a wide range of concentrations in the semi-concentrated to concentrated regime. To reveal the impact of geometry on kaolinite suspension's rheology, atomic force microscopy was employed, thus revealing unique information about the particle's structural differences. The apparent slip velocity was studied through the application of the Mooney technique using experimental data from parallel-plate geometry at various gap spacings. Sandpaper of varying grit was used to eliminate slip and estimate the true rheological parameters including the yield stress of these materials. Kaolinite suspensions were found to follow a Herschel–Bulkley model with yield stress that increases with concentration irrespective of the type of kaolinite particles. The aspect ratio and asperity of particles were found to alter their slip behavior by enabling the kaolinite network to have a tunable yield stress. It was also determined that the existence of resilient larger clusters at higher shear rates often induce higher slip effects.
In this study, we have carried out experiments to characterize the wall slip of colloidal suspensions of kaolinites. To demonstrate slip, the rheological measurements were carried out with parallel-plate geometry with smooth and rough plates. The asperities of the rough surface penetrated the slip layer and created a nearly no-slip region, whereas the smooth plate showed significantly higher slip, a conclusion drawn by comparing the macroscopic flow curves in both cases. Two slip regimes were identified, namely, (i) an elastic slip regime below the yield stress of the suspension where the material slips like a solid and (ii) a slip regime above the yield stress where the material yields and flows. The slip velocity was quantified using a simple phenomenological slip model that seems to capture slip in both flow regimes. The transition from the first slip regime to the other has been resolved numerically as the material starts yielding first at the edge of the parallel-plate geometry with the yield point propagating inwards as the rotational speed is increased. The numerical method also establishes uniquely the yield stress value, which was found to agree with data obtained from parallel-plate, cone-and-plate, and concentric cylinder geometries.
The flow behavior of nanocrystalline cellulose (CNC) hydrogels in the presence of a monovalent electrolyte (NaCl) as a function of CNC and salt concentration is explored using a variety of linear and nonlinear rheological tests. We have first observed an apparent “slip yield stress” at small wall shear stress values that is mainly due to the onset of solidlike slippage of the hydrogels before their true yielding and deformation. This flow regime and the “slip yield stress” can be eliminated using a sandpaper of an optimum grit size. At higher wall shear stress values, two yielding points for the CNC/salt network are seen in strain sweep tests due to network disruption and cluster deformation that depend on the concentration of both CNC (1–5 wt. %) and electrolyte (0–100 mM). The first yield stress is due to yielding and flow of clusters, while the second one is due to breakage of clusters to small flocs and individual fibers. These yielding stresses were obtained by a variety of tests including strain amplitude sweep, creep, and steady shear, and their values are compared confirming their existence. Rheo-SALS (small angle light scattering) measurements confirmed structural changes as the scattering patterns change from isotropic to highly anisotropic with an increase of deformation and rate of deformation. Moreover, confocal laser scanning microscopy and polarized microscopy images confirm the gradual breakup of clusters to smaller ones and eventually to nearly individual fibers with an increase in the applied shear strain and rate.