In ballasted track, the wheel load is transmitted to the subgrade via sleepers commonly made of impregnated wood, prestressed concrete, steel or recently developed polymer sleepers. Mentioned material types of sleepers are characterized by different elastic moduli being a key parameter in any numerical model. Hence, this paper aims to determine the elastic modulus of sleepers subjected to a laboratory four-point bending test. Traffic resembling load level of 60 kN adopted from a typical axle load distributed by the rails to the sleeper was applied in a quasistatic and cyclic loading. The samples included sleepers made of polymers complemented with wood and pre-stressed concrete. The results of this paper are based on the elastic modulus investigation. Main conclusions are focused on the sleeper’s elastic modulus under changing loading frequencies. Wood and prestressed concrete sleepers indicated mainly elastic behaviour resulting in a constant elastic modulus. However, polymer sleepers showed a loading frequency dependent elastic modulus as a result of their viscous elastic behaviour. Moreover, the conclusions of this paper involve E -modulus measurements of impregnated beech sleepers in order to describe their piece by piece elasticity variation due to their natural origin.
15 September 2021 in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
Before a new type of railway sleeper can be used in track, standardised laboratory tests must be carried out to determine its suitability. In addition to static load tests, assessments usually include cyclic load tests consisting of millions of load cycles, representing passing trains during the sleeper’s service life. In these laboratory tests, the loading cycles are applied continuously without resting periods to condense the test time. Traditional sleeper materials (timber, concrete) possess elastic properties for which such testing is appropriate. However, polymer sleepers exhibit viscoelastic properties, such as creep, a loading rate-dependent stiffness and heating due to non-linearity of the stress-strain curve. Subjecting polymer sleepers to continuous cyclic load tests with a load frequency reflecting permissible track speed can cause the sleeper to heat up. Intermittent testing with pauses between numbers of load cycles is proposed in this paper as a possible solution. The aim is to propose a laboratory loading procedure that adopts a traffic-resembling load of a railway line, considering an effective compromise between polymer visco-elastic behaviour and time consumption of the laboratory tests. The loading frequency is kept at the desired strain rate for track evaluation, giving a representative sleeper stiffness and strength assessment. Exemplary tests with varying test arrangements and loading procedures were performed to quantify the effects of intermittent loading in comparison with continuous loading. The proposed method eliminated most of the test-induced creep and heat accumulation, resulting in a more representative stiffness and strength assessment, which justifies the proposed intermittent testing for polymer sleepers. The proposed intermittent procedure is an optional test regime in ISO 12856-2 for polymer sleeper testing.
Railway sleepers are traditionally made of hardwood, pre-stressed concrete or steel. However, emerging advanced materials, including polymers or composites, are investigated for a possible employment in the sleeper production. The main function of sleepers is to distribute forces they carry onto the trackbed, to support rails and keep the spacing between them, called the track gauge. The operating tolerance of the track gauge is critical for safety and is set by regulations. Generally, it is advisable to keep the track gauge deviation, as well as the sleeper length deviation influencing it, as low as reasonably practicable. In this article, the recommended limit values of the thermal expansion coefficient characterizing possible sleeper length deviation were evaluated. The recommendation considered allowed track gauge tolerance and the experimentally determined temperatures of a sleeper measured in the trackbed for a year. In addition, thermal expansion of a selected polymer in laboratory conditions was determined, representing an alternative material for the sleeper production. Consequently, it was compared with the limit and conservatively used materials. Furthermore, the same tested polymer, but utilizing chopped glass fibres to reduce the thermal expansion of the polymer, was also tested. Results show a positive impact of the glass reinforcement on the thermal expansion coefficient. The applicability of the selected polymer in the railway sleeper production from the perspective of the thermal expansion was discussed in the paper.
This article is related to the unique application of fly ash-based stabilizer in the track bed of a railway line. In detail, it is focused on following analysis methods of samples structure and properties. The long-term observation of the stabilizer layer is based on the periodical sampling which is done once per year for the following compression strength test. Results collected over one decade showed the increasing tendency of the compression strength which is attributed to formatting the C-A-S-H gel. It is assumed it is done within structural conversion caused by the alkali activation of aluminosilicate components. This phenomenon was proved using electron microscopy. The statistical analysis of the compression strength resulted significant deviations the presence of which may be based on grains, poor stirring the mixture during placing, predisposed surfaces or micro cracks created during sampling in the railway track bed. The main outcomes of the paper are findings from non-destructive methods of Micro-CT and of electron microscopy, which were performed on specimens for the purpose of displaying their microstructure and identifying non-homogeneities of the specimens.
This paper deals with the investigation of the fly ash-based stabilizer used as a layer in railway track bed. It is a “new” material in railway structures. The main purpose of stabilizer is to reinforce railway track bed. The above mentioned fly ash-based stabilizer is a mixture consists of fly ash from Chvaletice plant in the Czech Republic, FGD gypsum, calcium oxide and water. The laboratory tests of the fly ash-based stabilizer have started in 2000 in order to define the key physical properties and also material suitability in the field of railway substructure. For the purpose of the 1:1 scale material verification, a box device with dimensions of 990 × 800 × 2095 mm for full scale testing was designed. On the base of the laboratory tests the 330 m long trial section of railway track was stabilized at the Smiřice railway station. The test layer under track No. 3 was built in April 2005 and the extraction of the material for labora - tory test is done on regular basis - each spring and autumn. The paper is focused on sampling of the fly ash-based stabilizer by core drilling for following laboratory tests. The experience with in situ sampling in railway track bed led to recommendation summarized in the conclusion. The layer of stabilizer, which is placed under railway ballast and crushed stone, was uncovered and the boreholes with diameter 100 mm were done. According to the difficulty of sampling it was possible to extract only a small amount of specimens for the determination of the performance and durability of the fly ash-based stabilizer. It was necessary to exclude some of sampled specimens which with high probability include predisposed surface failures that might significantly affect the average value of the young's modulus. The goal was to choose three specimens for the pressure test. Ultrasonic method and also Impulse Excitation Method were chosen as non destructive test methods for the determination of dynamic modulus of elasticity, which could denote the suitable samples for the pressure test. At the end of the paper the results of determined young's modulus and dynamic modulus of elasticity are also described. The most important findings in the comparison of non-destructive and destructive tests are discussed. These results can significantly support the knowledge of the stabilizer in the long-term monitoring of the trial section in Smiřice.
The extent of the use of asphalt concrete in track bed layers is minimal in contrast to the application of granular materials mostly represented by coarse/fine crushed stone mixture. This article summarizes advantages and disadvantages of the use of asphalt concrete in the track bed construction and provides relevant literature research. The main part of this article focuses on the application of recycled asphalt concrete (so called R-material) in the track bed layer and its following non-destructive X-ray Micro Computed Tomography Method (Micro-CT) for the description of its structural parameters. The contribution of this research is based on the evaluation of the air void and soluble binder content of chosen recycled asphalt concrete. First, it was obtained from laboratory geotechnical models of a railway track, and then from the following implementation in a trial section of an operating railway track. The conclusion contains results of the R-material practical application and findings from Micro-CT.