An experimental plasma reforming reactor for conversion of CH 4 -CO 2 to synthesis gas (syngas) has been developed, in which the plasma is generated by a nonthermal arc plasma torch with simple and compact structure. The effects of total flux of feed gases and the molar ratio of CH 4 /CO2 on syngas production, selectivities of H 2 and CO, and energy conversion efficiency were investigated. It is proven that this kind of plasma is an effective way to reforming of CO 2 -CH 4 with energy conversion efficiency of 5.25 mmol/kJ and energy efficiency of 81%. Moreover, the heat generated by the plasma can be fully utilized to activate catalyst.
Boron carbide (B4C) coatings are prepared by an RF inductively coupled plasma (ICP) torch with different amounts of hydrogen introduced into the sheath gas. The effects of the added hydrogen on the characteristics of the plasma are diagnosed by optical emission spectroscopy and high speed photography. The effects on the melting of B4C particles in the plasma are studied by scanning electron microscopy (SEM). The microstructure of the B4C coatings was determined with SEM imaging and x-ray diffraction analysis. The results show that adding hydrogen to the sheath gas leads to plasma contraction, which results in higher gas temperature of plasma. It also enhances B4C particles spheroidizing and improves the compactness of B4C coatings. Plasma processing does not change the main phase of boron carbide. The obtained results on B4C coatings on Cu substrates allows for improving the B4C coatings fabrication process.
Hydrogen plasma heating, a unique method for heating and reducing iron ore, is distinguished by its high heat, rapid reduction, and high efficiency, making it a promising technique in the metallurgy field. In this study, a non-transferred arc plasma heating system was used with Ar-H2 as the working gas and acidic pellets as the raw material. The microstructures and elemental distributions of the slag and iron phases during the reduction process were examined using electron microscopy and energy-dispersive X-ray. The variation patterns of Fe-containing phases in the reduction products were found using X-ray diffraction and full-spectrum fitting refinement. The conversion rate of the oxidized pellets and the deoxidation conversion rate per area were estimated for various gas flow rates and reduction times. A reaction kinetics model was also used to study the reaction controlling step. The results showed that during the reduction process, with an H2 flow rate of 4.5 L min−1 and a 40 min reduction, the conversion(α) reached 99.89% and the purity of the reduced metallic iron reached 99.9%, achieving the industrial-grade 3N standard. Si and Al in the melt bath generated fayalite (Fe2SiO4) and hercynite (FeAl2O4) with FexO. The deoxidation conversion rate per unit area was 1.11 g (cm2 min)−1. A three-dimensional diffusion-controlled model was used to describe the reduction process, and the mechanism function was 2/3(1 + α)3/2[(1 + α)1/3]−1. The values of the reduction reaction rate constant (K) were 12.6 × 10−2 s−1 and 12.8 × 10−2 s−1 when the flow rates of H2 gas were 3 and 4.5 L min−1, respectively. The apparent activation energy was 21.9 kJ mol−1. The empirical equation for the specific reduction rate was calculated as ln r = −2637.5/T − 0.407.
Yttrium oxide (Y2O3) is a crucial protective material for the inner walls of semiconductor etching chambers. This study employed Suspension Plasma Spray (SPS) technology to deposit Y2O3 coatings on AISI 304 stainless steel substrates. A water ring guide cover, which injects deionized water toward the center of the plasma flame at the torch outlet, was installed. The critical parameter ratio between the water ring flow rate and the suspension feed rate was investigated, with a specific focus on its influence on the coating’s microstructure and mechanical properties. The findings reveal that this parameter exhibits a significant positive correlation with porosity, with the coefficient of determination R2 for their linear fit reaching 0.91236. When the water ring flow rate ratio was reduced to 79.66%, the porosity decreased to 0.946%, while the primary composition of the coating remained unchanged. Bond strength tests demonstrated that the adhesion strength of the coating exhibits an upward trend with increasing proportion of water ring flow. The adhesion strength reached its maximum value of 27.02 MPa when the water ring flow rate proportion was increased to 85.45%. Roughness exhibits a non-monotonic variation trend within the ratio range, attaining its optimal minimum value at the lower end of the ratio, indicating complex interrelationships among process characteristics. This work concludes that a low water ring flow rate ratio is essential for fabricating dense, well-adhered, and smooth Y2O3 coatings via SPS, providing a critical guideline for process optimization for applications such as semiconductor protection.