Jialong Yang

Dr. Jialong Yang


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 June 2022 in Coatings
Verified
Journal Article
Open access
PDF file
HMHaobo Mao
Haobo Mao
Yingyi ZhangYingyi Zhang
Yingyi Zhang
JWJie Wang
Jie Wang
KCKunkun Cui
Kunkun Cui
HLHanlei Liu
Hanlei Liu
JYJialong Yang
Jialong Yang
TiC ceramics have the characteristics of high melting point and density, and titanium reserves on earth are extremely large; therefore, TiC ceramics are considered ultra-high temperature materials with great research value. However, the development of TiC-based ultra-high temperature composites has been seriously hindered by their poor mechanical properties. At present, improvement of the mechanical properties of TiC is mainly accomplished by adding a second phase. In this paper, the research status of modified elements-, nitrides-, and metal-reinforced TiC matrix composites is presented. The microstructure, phase composition, and toughening mechanism of TiC matrix composites reinforced by a second phase are described. The influence of the reaction products on the matrix during the toughening process is also discussed.

4 August 2022 in Coatings
Verified
Journal Article
Open access
PDF file
HWHongliang Wu
Hongliang Wu
LYLaihao Yu
Laihao Yu
SCShengchao Chang
Shengchao Chang
Yingyi ZhangYingyi Zhang
Yingyi Zhang
JYJialong Yang
Jialong Yang
With the development of large-scale blast-furnace and oxygen-rich coal-injection technology, as well as national green and low-carbon policy requirements, the ironmaking process has increasingly strict requirements for blast-furnace raw materials, such as new and higher requirements for coke quality and thermal performance. In this study, the melting loss reaction in a blast furnace was simulated under laboratory conditions and the microstructure evolution of coke after melting loss under CO2 and CO2 + H2O conditions was studied. The results showed that under a CO2 atmosphere, the specific surface area and pore volume of coke and the number of micropores in coke first increased and then decreased with the increase in reaction time, while the average pore size first decreased from 17.289 to 8.641 nm and then increased to 9.607 nm. In the gasification reaction between CO2 and coke, the relative content of the graphitized structure (IG/IAll) increased first, then decreased and then increased with the increase in reaction time, while the change trends of disordered structure (ID3/IG) and unstable structure (ID4/IG) were opposite to IG/IAll, indicating that coke still tended to be more orderly with the increase in time. In the mixed atmosphere of CO2 and H2O, the specific surface area and IG/IAll of coke increased with the increase in H2O content. However, when the proportion of H2O exceeded 50%, the specific surface area decreased slightly, and the pore-size value corresponding to the peak value in the pore-size distribution curve shifted to the right, and the average pore-size increased in the nanosize range.
1

21 November 2024 in Metals
Verified
Journal Article
Open access
PDF file
XZXiaoping Zhang
Xiaoping Zhang
ZFZihao Fan
Zihao Fan
AMAo Mi
Ao Mi
JCJunqiang Cong
Junqiang Cong
ZHZhenghong Hu
Zhenghong Hu
BWBaoliang Wen
Baoliang Wen
The reduction of hematite with ammonia is a potentially environmentally friendly method of ironmaking. Previous studies on ammonia reduction of pellets typically involved samples weighing only 2.8 g and lacked detailed activation energy analysis for the ammonia-hydrogen co-reduction of pellets. Therefore, to further investigate the reduction thermodynamics and kinetics of NH3–H2 reduction of pellets, this study uses 50 g pellets for reduction experiments. By increasing the pellet mass, the study expands the scope of kinetic research on ammonia reduction of pellets. The results indicate that nitrogen gas produced from ammonia decomposition reduces the equilibrium components of the reducing gas. In the temperature range of 700–850 °C, the formation of iron nitride exhibits a narrow range during ammonia reduction of hematite. In the reduction of 50 g of pellets, the reduction rate using 100% NH3 is lower than that using a 50% NH3 and 50% H2 mixed gas, which is, in turn, slower than using 100% H2. As temperature increases, the reduction effect of 50% NH3 and 50% H2 approaches that of 100% H2. Among common gas-solid reaction mathematical models, the Phase-boundary-controlled model with the Contracting Cylinder Model is selected as the most plausible mechanistic function. For the reduction of 50 g of pellets, the activation energies for reactions using 100% NH3, 50% NH3 and 50% H2, and 100% H2 are 65.42, 54.37, and 29.17 kJ/mol, respectively. The decomposition of NH3 has a negative effect on the reduction of Fe2O3. XRD analysis and electron microscopy element line scanning show that Fe4N is formed during the reduction of Fe2O3 with 100% NH3. The use of a 50% NH3 and 50% H2 mixture significantly reduces the formation of Fe4N during the reduction of the pellets.

24 July 2024 in Journal of Iron and Steel Research International
Verified
Journal Article
Closed access
PDF file
BWB.L. Wen
B.L. Wen
ZFZ.H. Fan
Z.H. Fan
JLJ.X. Li
J.X. Li
DLD.L. Liu
D.L. Liu
JYJialong Yang
Jialong Yang

1 January 2024 in High Temperature Materials and Processes
Verified
Journal Article
Open access
PDF file
JYJian Yang
Jian Yang
LYLaihao Yu
Laihao Yu
Yingyi ZhangYingyi Zhang
Yingyi Zhang
ZHZhichen Han
Zhichen Han
JYJialong Yang
Jialong Yang
The gas flow distribution inside a blast furnace affects its smelting. Laser surface detection technology can control the gas flow distribution and promote the stable and smooth running of blast furnace by observing and adjusting the surface condition in the blast furnace in real-time. The laser surface inspection technology in blast furnace gas flow control and optimization was introduced, with Masteel 4,000 m 3 blast furnace as an example. The results showed that the 30 W high-power laser had good penetration performance and could obtain clear scanning images of the material surface. In the process of strengthening smelting, the laser detection system determined that the central airflow of blast furnace was insufficient, resulting in a decrease in furnace condition stability, and promptly took measures to adjust the angle of the mineral coke fabric equipment and lifting line. After adjusting the material line, the central airflow was properly suppressed and stabilized, the angle of edge platform increased, the airflow developed properly, and two suitable gas flows were formed, which finally stabilized the furnace condition. Meanwhile, the small duct airflow other than the central airflow was found in time through the laser detection system, which provided conditions for operators to take measures to effectively eliminate the duct airflow, thereby avoiding big impacts on the blast furnace operation and technical and economic indexes. Therefore, the laser surface detection technology could effectively judge the gas flow distribution in the furnace, which contributed to timely adjustment of process parameters and optimization of blast furnace operation.

1 January 2023 in Journal of Mining and Metallurgy, Section B: Metallurgy
Verified
Journal Article
Open access
PDF file
BWB.-L. Wen
B.-L. Wen
XZX.-P. Zhang
X.-P. Zhang
DLD.-L. Liu
D.-L. Liu
JLJ.-X. Li
J.-X. Li
XSX.-D. Sun
X.-D. Sun
JYJialong Yang
Jialong Yang
Ultrafine iron ore concentrate pose challenges such as poor pellet formation performance, low-bursting temperature, and a complex drying thermal regime. To examine the drying characteristics of green pellets made from ultrafine iron ore concentrate, the Weibull distribution function and Dincer model were employed to fit and analyze the corresponding drying curve. The effects of drying temperature and air speed on the strength of dried pellets were also studied. The findings revealed that the drying process of green pellets of ultrafine iron ore concentrate involved three stages: ascending speed, constant speed, and descending speed. As the drying temperature and air speed increased, the drying time decreased. The coefficient of determination R2 for the fitted Weibull distribution function model ranged from 0.995 to 0.998, while the R2 value for the Dincer model ranged from 0.990 to 0.996. Both fitted models aligned with the experimental data and proved to be effective. According to the Bi values obtained through the Dincer model, raising the drying air speed in the initial stage and the drying air temperature in the subsequent stage of the drying system could efficiently remove moisture, reduce the risk of green pellet rupture, and maintain productivity. The moisture diffusion coefficient and convective mass transfer coefficient increased with rising temperature and air velocity, following the order of Deff > Dcal > D*eff as determined by the Weibull distribution function, Dincer model, and Fick?s second law. Additionally, the activation energy value of ultrafine iron ore concentrate for drying derived from the Arrhenius formula was 4515.60 J/(mol?K). Notably, increasing the drying temperature increased the strength of the dried particles due to their more compact and dense internal structure. This study offers theoretical support for simulating the drying of green ultrafine iron ore concentrate pellets and provides guidelines for selecting diverse drying conditions and designing drying equipment.