Kamil Banaszek

Mr. Kamil Banaszek

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 January 2023 in Materials
Verified
Journal Article
Open access
PDF file
TSTomasz Szatkiewicz
Tomasz Szatkiewicz
APAndrzej Perec
Andrzej Perec
ARAleksandra Izabela Radomska-Zalas
Aleksandra Izabela Radomska-Zalas
KBKamil Banaszek
Kamil Banaszek
Błażej BałaszBłażej Bałasz
Błażej Bałasz
Composites are materials with a heterogeneous structure, composed of two or more components with different properties. The properties of composites are never the sum or average of the properties of their components. There is a lot of research and many models on the different property assessments of composite materials. Composites are used as construction materials in key areas of technology, including in civil and mechanical engineering, aviation and space technology, and others. This work presents a modern composite material created with 3D-printing technology using the SLM method, and the possibility of its processing with one of the advanced manufacturing technologies, i.e., the Abrasive Water Jet (AWJ). Tests planned using DoE methods were carried out by changing control parameters such as the pressure, abrasive flow, and traverse speed. As a dependent parameter, the surface roughness parameter Sq (squared mean height) was selected and measured in different places of the cut composite. Based on the S/N ratio, the most favorable control parameters of the cutting process were also determined to achieve the lowest roughness of the cut surface. A clear effect of the controlled cutting process on the surface roughness was observed, as well as roughness variation for the metal and polymer component. In addition, the contact surface of the polymer with the metal in the cut zone was analyzed. Analysis of the contact surfaces on the microscope showed that the gap between the polymer–metal contact surfaces does not exceed 2.5 μm.

21 December 2021 in Materials
Verified
Journal Article
Open access
PDF file
Dariusz LipinskiDariusz Lipinski
Dariusz Lipinski
KBKamil Banaszek
Kamil Banaszek
ŁRŁukasz Rypina
Łukasz Rypina
This paper presents an effectiveness analysis of the grinding process with the use of a new multi-layer abrasive tool. The designed abrasive tool consists of external layers with a conventional structure, whose task is to decrease the grinding wheel load and ensure high grinding volumetric efficiency. The inner layer of the grinding wheel contains a 30% addition of abrasive aggregates. The task of the inner layer is to provide lower roughness of the machined surface. The aim of the research presented in this paper was to evaluate the topography of the designed abrasive tool and to analyze the middle layer properties influencing the machined surface roughness. The differentiation of the active surface features of the abrasive tool was determined for the conventional layer and the layer with the addition of abrasive aggregates. The machining potential of the layers was also determined using the Shos parameter. The surface topography of Ti-6Al-4V alloys ground with the use of a multi-layer wheel and a conventional grinding wheel was analyzed. With the application of the bootstrap hypothesis, the set of roughness parameters differentiating the topography of ground surfaces was determined.

6 September 2022 in Materials
Verified
Journal Article
Open access
PDF file
ŁRŁukasz Rypina
Łukasz Rypina
Dariusz LipinskiDariusz Lipinski
Dariusz Lipinski
KBKamil Banaszek
Kamil Banaszek
Wojciech KacalakWojciech Kacalak
Wojciech Kacalak
FSFilip Szafraniec
Filip Szafraniec
The shape of the cutting blades of the abrasive grains has an influence on the material separation process in the machining zone. The paper analyzes the influence of the geometrical parameters of the abrasive grains (rake angle γ, apex angle ε, opening angle α), as well as width bz and length bb of the cutting zone on the material removal efficiency. The material removal efficiency was determined taking into account the volume of the removed material VG and the volume of lateral piles-up VR. The analyses were carried out on the basis of the results of experimental and simulations using the finite element method. The relationship between the selected geometric parameters characterizing the cutting zone and the coefficient characterizing the efficiency of the material removal process was determined. A strong influence of the opening angle α as well as the width bz and length bb of the cutting zone on the material removal process by abrasive grain was demonstrated. It was observed that the wide cutting edge, and thus the large opening angle α of the grain, reduced the size of the pile-ups and more effectively removed the chip material.

26 August 2022 in Materials
Verified
Journal Article
Open access
PDF file
Wojciech KacalakWojciech Kacalak
Wojciech Kacalak
Dariusz LipinskiDariusz Lipinski
Dariusz Lipinski
FSFilip Szafraniec
Filip Szafraniec
KBKamil Banaszek
Kamil Banaszek
ŁRŁukasz Rypina
Łukasz Rypina
In this article, the methodology of using probabilistic models of the grinding tool wear process is presented. Probabilistic modeling with empirical data allowed determining the values of other important process features. Among them, the distribution of active grains lifetime or distribution of cumulative attritious wear of the grinding grain apex could be distinguished. The results of modeling and wear analysis of grinding wheels as well as experimental results on peripheral grinding with zoned grinding wheels are presented. The analyzed grinding wheels consisted of three layers: two identical external layers with conventional structure and one internal layer containing the addition of abrasive aggregates. The external layers were profiled by chamfering the edges. As a result, their nominal surfaces were conical. The internal layer had a cylindrical shape and was designed for smoothing the surface after machining with external part. The tools were designed to increase the grinding efficiency and hence a good quality of machined surfaces could be acquired. For the experimental tests, the Ti6Al4V titanium alloy was used. It was found that the change in the shape and position of the grinding zone, as a result of volumetric wheel wear, caused a significant change in fracturing intensity. In the case of multilayer grinding tools, the wear process depends on the physical properties of each layer and their participation during machining of the workpiece. The presented methodology could be applied to a study on the machining process stages, which concerns temporary states and their variability according to the machining time.This makes it possible to reduce the cost of developing new tools dedicated to specific applications.

20 August 2022 in Materials
Verified
Journal Article
Open access
PDF file
Wojciech KacalakWojciech Kacalak
Wojciech Kacalak
FSFilip Szafraniec
Filip Szafraniec
Dariusz LipinskiDariusz Lipinski
Dariusz Lipinski
KBKamil Banaszek
Kamil Banaszek
ŁRŁukasz Rypina
Łukasz Rypina
In this article, a method of grinding small ceramic elements using hyperboloid and conical grinding wheels was presented. The method allowed for machining with a lower material removal speed and extending the grinding zone without reducing the efficiency of the process. In order to assess the process output parameters, numerical simulations were carried out for single-pass machining. This strategy allows for automation of the process. Grinding with a low material removal speed is recommended for the machining of small and thin elements, since this can avoid fracturing the elements. The methodology for selecting process parameters as well as the results of the abrasive grains activity analyses were presented. The analyses also concerned the roughness of machined surfaces and the variability of their textures. This grinding method was applied in the production of small ceramic elements that are used in the construction of electronic systems, and in the processing of small piezoceramic parts. This grinding technique could also be used in other grinding processes, where the removal of small machining allowances with high efficiency is required.

11 October 2024 in Precision Engineering
Verified
Journal Article
Open access
Dariusz LipinskiDariusz Lipinski
Dariusz Lipinski
ŁRŁukasz Rypina
Łukasz Rypina
KBKamil Banaszek
Kamil Banaszek
Robert TomkowskiRobert Tomkowski
Robert Tomkowski
Reducing plastic interactions between abrasive grains and the material being processed improves grinding efficiency and lowers energy consumption. Widening the cutting zone with abrasive grains enhances chip formation and reduces lateral material displacement. This can be achieved by using abrasive microaggregates. The paper presents an experimental analysis of grinding with modified wheels containing abrasive microaggregates. It examines how these microaggregates impact the grinding wheel's surface microgeometry and material removal efficiency. The study measured changes in the number, surface area, volume, and spacing of active contact areas on the grinding wheel active surface. A comparative analysis using the Shos indicator showed that abrasive microaggregates promote the formation of active areas with wide cutting edges perpendicular to the cutting direction. Finite element method simulations confirmed that abrasive microaggregates enhance material removal by widening the micro-cutting zone and increasing lateral resistance, which reduces the formation of flashes along the cutting path. The study also assessed how these surface features impact the roughness of the ground surface. A comparative analysis of roughness parameters showed a statistically significant reduction in surface, volume, hybrid, and functional parameters when using grinding wheels with abrasive microaggregates. This analysis was conducted using bootstrap statistical hypothesis tests.