Textured kaolinite and halloysite-based materials were shaped by tape casting in order to promote the alignment of clay particles along the tape casting direction and to investigate the structure evolution of these phyllosilicates during the dehydroxylation process. The crystallinity indexes HI and R2 of the starting kaolins (KRG and KCS) were determined and appeared close to values found for the well-ordered reference kaolin KGa-1b. The halloysite clay exhibited trimodal grain size distribution and tended to be less textured than KRG and KCS according to the (002) pole figures performed on green tapes. The constant heating rate derived kinetic parameters matched the expected range. We followed the dehydroxylation of kaolinite and halloysite through in situ high-temperature X-ray diffraction measurements at the ESRF synchrotron radiation source on the D2AM beamline. The dehydroxylation of these kaolinite and halloysite occurred between 425 °C and 675 °C for KRG and KCS and from 500 °C to 650 °C for halloysite. In addition, the evolution of the basal distance of kaolinite regarding the heat treatment temperature confirmed that the dehydroxylation process occurred in three steps: delamination, dehydroxylation, and formation of metakaolinite. The calculated coefficient of thermal expansion (CTE) along the c axe values were close to 17 × 10⁻⁶ °C⁻¹ for kaolinite (KCS and KRG) and 14 × 10⁻⁶ °C⁻¹ for halloysite.

Developing biofoams constitutes a challenging issue for several applications. The present study focuses on the development of a chitosan-based biofoam. Solutions of chitosan in acetic acid were dried under vacuum to generate foams with high-order structures. Chitosan concentration influenced significantly the morphology of developed porosity and the organization of pores in the material. Physico-chemical characterizations were performed to investigate the effects of chitosan concentration on density and thermal conductivity of foams. Even if chitosan-based biofoams exhibit interesting insulating properties (typically around 0.06 W·m⁻¹·K⁻¹), it has been shown that their durabilities are limited when submitted to a wet media. So, a way of application consists to elaborate a ceramic material with open porosity from a slurry prepared with an organic solvent infiltrating the porous network of the foam.

Halloysite and kaolinite are dioctahedral TO phyllosilicates that drive the interest of scientists for formulating environmentally friendly materials, and consequently in the field of ceramics. The main scope of this study was the understanding of the texture evolution upon the dehydroxylation reaction and the influence of the presence of halloysite. In situ synchrotron (002) and (111) poles figures were recorded on the DiffAbs beamline at SOLEIL Synchrotron, from room temperature to 1000 °C, on kaolinite and/or halloysite-rich samples shaped by tape casting. Commercial kaolins and halloysite provided by Imerys company were used. The samples were labeled KRG100, KCS100, H100, KRG50H50 and KRG59H50 in relation with the wt. % of kaolin (KRG, KCS) or halloysite (H) clays. In samples KCS100 and KRG100, a strong texture was observed until in situ annealing at 700 °C, with respect to the c-axis of kaolinite. On the contrary, the texture with respect to the c-axis of halloysite for the sample H100 was weak whatever the temperature was. Moreover, this weak texture disappeared before the complete dehydroxylation of halloysite. This is due to the opening of some halloysite tubes. When considering the samples KRG50H50 and KCS50H50, a significant texture was observed with the c-axis preferentially oriented perpendicular to the sample surface. The presence of kaolinite platelets predominated onto the alignment of halloysites tubes. Furthermore, it was noted that the halloysite influenced the (002) diffracted intensity into the temperature range 20 °C to 400 °C. Above 400 °C, the behavior obtained for the (002) reflection in samples KRG50H50 and KCS50H50 was similar to the behavior noticed for pure kaolins KRG100 and KCS100, respectively. The dehydroxylation temperature range appeared to be relevant with combined effect of kaolinite and halloysite transformations arising from KRG100 or KCS100 and H100 samples. Therefore, the onset point of dehydroxylation is 550 °C ± 25 °C for KRG100, KCS100, KRG50H50 and KCS50H50. For the pure halloysite H100 sample, the dehydroxylation starts at the lower temperature 475 °C. It was also noted that during the dehydroxylation of kaolinite, the characteristic portion of ring related to the diffracted intensity of the (111) reflection located at χ = 45° tended to disappear above 550 °C and led to the formation of a new transitory phase with a (111) reflection with perpendicular alignment to the c-axis. Indeed, an epitaxial relationship with the (111) kaolinite reflection could be assumed. Further X-ray scattering experiments allowed highlighting the effective offset temperature of the dehydroxylation, which was identified as close to 720 °C. The metakaolinite achieved structural transformation to another transitory phase at 1000 °C.

This study investigates the use of a methylcellulose binder in extrusion additive manufacturing of 316L as an alternative to common wax-based binders. Various quantities of copper (Cu) powder were also added in the paste composition to attempt to reduce the sintering temperature by promoting persistent liquid phase sintering. Debinding experiments were conducted under different temperatures and dwell times using argon (Ar), Ar/5%H₂, and Ar/1%O₂ atmospheres. Debinding reduced carbon (C) content to 0.032 wt.% by using a two-step debinding process of Ar/5%H₂ and Ar/1%O₂ thermal treatments. Using this debinding process, sintering was conducted at 1200 °C under Ar/5%H₂ atmosphere with the presence of 0, 10, and 20 vol.% Cu in the paste. Microstructure, mechanical, and corrosion properties were studied. Cu additions allowed the improvement of the densification when sintering at 1200 °C was performed. A 20 vol.% Cu addition yielded 88% relative density after sintering for 10 h, while pure 316L powder sintered under the same conditions had 70%. Mechanical properties were inferior to fully dense stainless steel, but it is not clear if this is due to the Cu additions or insufficient densification.