A poly(vinylidene co-hexafluoropropylene) (PVDF-HFP) membrane is functionalized with polyaniline (PANI) and graphene oxide (GO) nanoparticles. The obtained PVDF-HFP polymer electrolyte membranes (PEMs) have been characterized and implemented in lithium-ion batteries. As a result, the PVDF-HFP/PANI membrane shows the highest ionic conductivity (IC) of 1.04 × 10−3 mS cm−1 compared to pristine PVDF-HFP and PVDF-HFP/PANI/GO ternary membrane; however, PANI addition decreases the tensile strength of the PVDF-HFP membrane from 4.2 MPa to 2.8 MPa. Therefore, GO is introduced to recover the reduced mechanical strength of the PVDF-HFP/PANI membrane. The obtained PVDF-HFP/PANI/GO ternary membrane shows a remarkable improvement in tensile strength of up to 8.8 MPa; however, slight reduction is observed in the ionic conductivity of 6.64 × 10−4 mS cm−1. Furthermore, the PVDF-HFP/PANI/GO ternary membrane exhibits outstanding thermal and mechanical stabilities, improved morphology, highest electrolyte uptake (367.5%) and an excellent porosity of around 89%. Moreover, the PVDF-HFP/PANI/GO ternary PEM has been successfully applied in a lithium-ion battery, which can retain over 95% capacity after 30 cycles. Therefore, the proposed PVDF-HFP/PANI/GO ternary membrane can be a promising candidate as a separator in future lithium-ion batteries.
3 September 2018 in Malaysian Journal of Fundamental and Applied Sciences
Solid oxide fuel cells (SOFCs) are efficient yet environmentally benign devices that can convert chemical energy into electrical energy and heat for large scale of applications. However, higher operating temperature of this device limits the selection of proper materials to be used as electrode and electrolyte as well as sacrifices the durability. Thus, it is desirable to develop materials with superior electrochemical performance at intermediate temperature (600-900 oC) for SOFC. LaSrCoFeO3 (LSCF) doped with CuO is an attracting yet promising cathode material for IT-SOFC owing to the distinguish properties including high electrical conductivity and high catalytic activity for the oxygen reduction reaction. This work investigates the influence of the synthesis route which are sloid state route and sol-gel route towards chemical and physical properties of composite LSCF-CuO. The samples were synthesized at different temperature ranging from 600 oC to 900 oC for each route respectively. XRD results showed high purity of as-synthesized samples while in the meantime increased in crystallinity has been observed as increased in calcining temperature indicating bigger crystal size after calcined at 900 oC. SEM images showed LSCF-CuO particles tends to expand as the calcining temperature increased. Meanwhile, from TGA results it is clear to conclude that LSCF-CuO loss its weight significantly after calcined at designed temperature.
A mixture of lanthanum strontium cobalt ferrite (LSCF) and nickel oxide (NiO) makes for a desirable cathode material for an IT-SOFC due to its excellent oxygen reduction capability. This study investigates the effect of NiO addition into LSCF cathode on its physical and electrochemical properties. To optimise the amount of NiO addition, both electrochemical impedance spectra and bode phase were used to examine various weight ratios of nickel oxide and LSCF cathode. Brunauer-Emmett-Teller (BET) and thermal analyses validated the electrochemical observation that the LSCF:NiO ratio yields sensible oxygen reduction reaction and stoichiometric findings. Initial characterisation, comprising of phase and bonding analyses, indicated that LSCF-NiO was successfully synthesised at 800 °C using an improved modified sol gel technique. The addition of 5% nickel oxide to LSCF results in the lowest area specific resistance (ASR) value overall. The Bode phase implies that the addition of 5% nickel oxide to LSCF reduces the impedance at low frequencies by 64.28 percent, indicating that a greater oxygen reduction process happened at the cathode. After the addition of 5 wt% NiO, a single LSCF-NiO cell may function at temperatures as low as 650 °C and the LSCF cathode power density is increased by 25.35%. The surface morphology of the LSCF-NiO cathode reveals that the average particle size is less than 100 nm, and mapping analysis demonstrated a homogenous NiO distribution over the cathode layer. Consequently, the synthesis of LSCF-NiO at intermediate temperatures (800–600 °C) revealed outstanding chemical compatibility, bonding characteristics, and electrochemical performance.
25 July 2023 in International Journal of Technology
This study investigates the impact of zinc oxide on the physical characteristics and electrochemical behavior of the LaSrCoFe (LSCF) cathode. Electrochemical impedance spectra in conjunction with the bode phase were used to optimize the amount of zinc oxide addition in the LSCF cathode. Brunauer-Emmett-Teller (BET) and thermal analysis were utilized to substantiate the electrochemical discovery that the LSCF: ZnO ratio yields rational oxygen reduction reaction and stoichiometric outcomes. Initial characterization, comprising of phase and bonding analyses, indicated that LSCF-ZnO was successfully synthesized at 800 ºC using an improved modified sol-gel technique. The addition of 5% zinc oxide to LSCF results in the lowest overall area-specific resistance (ASR) rating. The Bode phase implies that the addition of 5% zinc oxide to LSCF reduces the low-frequency impedance by 64.28%, indicating that the cathode experienced a greater oxygen reduction reaction. After the addition of 5% zinc oxide, a single LSCF-ZnO cell may function at temperatures as low as 650 °C, and the LSCF cathode power density is increased by 25.35%. The surface morphology of the LSCF-ZnO cathode reveals an overall particle size of less than 100 nm, and mapping analysis reveals a homogeneous distribution of ZnO over the cathode layer. Consequently, LSCF-ZnO demonstrated outstanding chemical compatibility between LSCF and ZnO, bonding characteristics, and electrochemical performance with the capacity to function at an intermediate temperature (600 °C – 800 °C).
11 October 2025 in International Journal of Hydrogen Energy