The study of plasma instabilities is a research topic with fundamental importance since for the majority of plasma applications they are unwanted and there is always the need for their suppression. The initiating physical processes that seed the generation of plasma instabilities are not well understood in all plasma geometries and initial states of matter. For most plasma instability studies, using linear or even nonlinear magnetohydrodynamics (MHD) theory, the most crucial step is to correctly choose the initial perturbations imposed either by a predefined perturbation, usually sinusoidal, or by randomly seed perturbations as initial conditions. Here, we demonstrate that the efficient study of the seeding mechanisms of plasma instabilities requires the incorporation of the intrinsic real physical characteristics of the solid target in an electro-thermo-mechanical multiphysics study. The present proof-of-principle study offers a perspective to the understanding of the seeding physical mechanisms in the generation of plasma instabilities.

This article addresses key features for the implementation of low current pulsed power plasma devices for the study of matter dynamics from the solid to the plasma phase. The renewed interest in such low current plasma devices lies in the need to investigate methods for the mitigation of prompt seeding mechanisms for the generation of plasma instabilities. The low current when driven into thick wires (skin effect mode) allows for the simultaneous existence of all phases of matter from solid to plasma. Such studies are important for the concept of inertial confinement fusion where the mitigation of the instability seeding mechanisms arising from the very early moments within the target’s heating is of crucial importance. Similarly, in the magnetized liner inertial fusion concept it is an open question as to how much surface non-uniformity correlates with the magneto-Rayleigh–Taylor instability, which develops during the implosion. This study presents experimental and simulation results, which demonstrate that the use of low current pulsed power devices in conjunction with appropriate diagnostics can be important for studying seeding mechanisms for the imminent generation of plasma instabilities in future research.

Laser WakeField Acceleration (LWFA) is extensively used as a high-energy electron source, with electrons achieving energies up to the GeV level. The produced electron beam characteristics depend strongly on the gas density profile. When the gaseous target is a gas jet, the gas density profile is affected by parameters, such as the nozzle geometry, the gas used, and the backing pressure applied to the gas valve. An electron source based on the LWFA mechanism has recently been developed at the Institute of Plasma Physics and Lasers. To improve controllability over the electron source, we developed a set of 3D-printed nozzles suitable for creating different gas density profiles according to the experimental necessities. Here, we present a study of the design, manufacturing, evaluation, and performance of a 3D-printed nozzle intended for LWFA experiments.

The computational study of x-pinch plasmas driven by pulsed power generators demands the development of advanced numerical models and simulation schemes, able to enlighten the experiments. The capabilities of PLUTO code are here extended to enable the investigation of low current produced x-pinch plasmas. The numerical modules of the code used and modified are presented and discussed. The simulations results are compared to experiments, carried out on a table-top pulsed power plasma generator implemented in a mode of producing a peak current of ∼45 kA with a rise time (10%–90%) of 50 ns, loaded with Tungsten wires. The structural evolution of plasma density is studied and its influence on the magnetic field is analyzed with the help of the new simulation data. The simulated areal mass density is compared with the experimentally measured dense opaque region to enlighten the dense plasma evolution. In addition, the measured areal electron density is compared to the simulation results. Moreover, the new simulation data offer valuable insights to the main jet formation mechanisms, which are further analyzed and discussed in relation to the influence of the J × B force and the momentum.

An experimental and numerical study of the nanosecond electrical explosion dynamics of bare and dielectric coated metallic wires in vacuum is reported. A table top Z-pinch generator down-tuned to generate a peak current of 40 kA with a rise time of 60 ns is implemented for the experiments in the skin effect mode. Optical probing diagnostics as well as multiphysics–multiphase simulations are used to study the spatiotemporal dynamics of the exploded wire from the solid to the plasma phase. The results show that the inclusion of the dielectric coating mitigates the electro–thermo–mechanical instability growth developed prior to plasma formation, which results in a subsequent reduced magnetohydrodynamic instability growth in the plasma phase. The study offers valuable insights into the understanding of the seeding mechanisms for the generation of plasma instabilities and the efforts for their growth rate suppression.

A three-dimensional, thermal-structural finite element model, originally developed for the study of laser–solid interactions and the generation and propagation of surface acoustic waves in the macroscopic level, was downscaled for the investigation of the surface roughness influence on pulsed laser–solid interactions. The dimensions of the computational domain were reduced to include the laser-heated area of interest. The initially flat surface was progressively downscaled to model the spatial roughness profile characteristics with increasing geometrical accuracy. Since we focused on the plastic and melting regimes, where structural changes occur in the submicrometer scale, the proposed downscaling approach allowed for their accurate positioning. Additionally, the multiscale simulation results were discussed in relation to experimental findings based on white light interferometry. The combination of this multiscale modeling approach with the experimental methodology presented in this study provides a multilevel scientific tool for an in-depth analysis of the influence of heat parameters on the surface roughness of solid materials and can be further extended to various laser–solid interaction applications.