In this research, solvothermal synthesized MoSe2 nanosheets were analyzed to determine their structure and optical properties. Measurements through atomic force microscopy, scanning electron microscopy, and transmission electron microscopy confirmed the formation of MoSe2 nanosheets. The energy-dispersive x-ray results revealed the presence of high-purity MoSe2 and an atomic percentage ratio of Mo:Se ∼ 1:1.93. Additionally, x-ray diffraction and Raman showed the crystal structure of MoSe2 and the existence of a two-dimensional (2D) layer, respectively. The linear optical properties of the MoSe2 nanosheets were analyzed by Fourier transform infrared (FTIR) spectroscopy and the Kramers–Kronig method. The FTIR research indicated the vibrational modes of several chemical groups, thus proving the presence of MoSe2 ions. For the varying concentrations of MoSe2 nanosheets in dimethylformamide, the third-order nonlinear optical properties of MoSe2 nanosheets were determined in detail using the Z-scan approach and a continuous-wave Nd:YAG laser. As the transmittance measurements in an open aperture Z-scan setup indicated, all the synthetized samples had saturable absorption. Similar investigations using a close-aperture Z-scan technique proved that all samples had nonlinear refractive indices in the range of 10−7 cm2/W with a positive sign and self-focusing behavior. Moreover, the third-order susceptibility and the figure of merit were found to be in the order of 10−5 esu and 10−4 esu cm, respectively. The findings of this study provide insight about modified 2D materials and expand the use of MoSe2 nanosheets in photonic devices.
8 November 2022 in Physical Chemistry Chemical Physics
If the conductivity and thermal properties of polyurethane films are improved with fillers, they can be used in wearable electronics, strain sensors, etc.
The flexible film of polyurethane/graphene (PU/G) composition with the different mass fractions of reduced graphene oxide (rGO) was synthesized by the in situ polymerization method and the electrothermal properties of the films were investigated. Results show by increasing the mass fraction of rGO to 5 wt% (PU/G5), the composition goes to the percolation zone. Further, the PU with 20 wt% of rGO (PU/G20) shows good conductivity which is relatively stable at different voltages (∼135 Ω/sq). Moreover, using graphene in the PU matrix has increased its thermal stability. PU/Gs stable up to 200 °C by assisting graphene. Also, the maximum Seebeck coefficient and voltage of PU/Gs (5, 10, 20) obtain at about 45 °C and 85 °C respectively, and PU/G20 has better performance than others. In addition, the electrothermal response of PU/G20 shows good repeatability and could reach 75 °C and 45 °C by applying the 22 V and 12 V respectively. The thermal stability, good electrothermal response, and flexibility of the sample suggest it for electrical heaters and wearable applications.
Here, we prepared ultra-small black phosphorene quantum dots (BPQDs) using a liquid exfoliation method involving sonication. The structural features of BPQDs have been investigated using TEM, AFM, Raman, UV-visible, PL, and FTIR analysis. The morphological analyses show the 1-7 layer of BPQDs with an average size of about 4-5 nm. The spectroscopic analyses of BPQDs imply absorption in the UV wavelength region and band gap energy of about 3.3 eV. Also, in the case of excitation with the wavelength of the UV region, a blue shift emission is seen in the PL spectrum. The P = O, O-P-O and O = P-OH bonds are seen in the FTIR spectrum. Using the FTIR spectrum and Kramers–Kronig (KK) relation, some optical properties of BPQDs, such as refractive index, dielectric function, and frequencies of an optical phonon (transverse (TO) and longitudinal (LO)) were obtained. As well as utilizing the Z-scan technique, the nonlinear refractive index (n2) and nonlinear absorption coefficient (β) were achieved. The closed-aperture (CA) Z-scan testing indicated the self-defocusing of BPQDs. Also, the open aperture (OA) Z-scan traces of the BPQDs with a valley-like pattern expressed the two-photon absorption (2 PA). So, BPQD, as a new material, is a promising candidate for optical and nano-electrical devices.
Photodetectors based on Armchair-Silicene-Nanoribbons (ASiNR) with asymmetric source (Ir-doped silicene) and drain (Cu-, Ag-, or Au-doped silicene) contacts have been simulated employing tight-binding approximation coupling to Non-Equilibrium Green’s Function (NEGF) approach. Monochromatic 1 kW cm−2 illumination in the range of 0.1–10 eV has been used for the simulation of the photocurrent, photoresponsivity, quantum efficiency, and detectivity. It is shown that the highest peak in the photocurrent spectrum occurs at the 273 nm incident wavelength for all devices, and the Ir-Cu device has presented enhanced photodetector characteristics than Ir-Ag and Ir-Au devices. It is also found that only transitions between two subbands with identical indexes are allowed. Moreover, the first peak in the photocurrent spectrum is related to the main band gap of ASiNR. Additionally, the simulated dark and total currents versus source-drain voltage reveal that photocurrent caused a negative shift in the total current proportional to incident light intensity.