Mondiu Durowoju

Dr. Mondiu Durowoju


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 February 2019 in Materialwissenschaft und Werkstofftechnik
Verified
Journal Article
Closed access
PDF file
MDMondiu Durowoju
Mondiu Durowoju
Rotimi SadikuRotimi Sadiku
Rotimi Sadiku
SDS. Diouf
S. Diouf
MSM.B. Shongwe
M.B. Shongwe
IMI.M. Makena
I.M. Makena
AEA.A. Eze
A.A. Eze

31 May 2023 in Sustainability
Verified
Journal Article
Open access
PDF file
AOAkinola David Ogunsola
Akinola David Ogunsola
MDMondiu Durowoju
Mondiu Durowoju
Oyetola OgunkunleOyetola Ogunkunle
Oyetola Ogunkunle
TPTimothy Laseinde, PhD
Timothy Laseinde, PhD
S M RahmanS M Rahman
S M Rahman
I. M. R. FattahI. M. R. Fattah
I. M. R. Fattah
The implementation of biodiesel in internal combustion engines has been observed to enhance engine performance and mitigate the discharge of toxic gaseous emissions from the engine. In this research, Shea Butter Oil Biodiesel (SBOB) was used to operate a diesel engine to analyze the performance and emissions characteristics. Shea Butter Oil Biodiesel (SBOB) was blended with petroleum diesel in ratios 0:100 (B0), 25:75 (B25), 50:50 (B50), 75:25 (B75), and 100:0 (B100). The torque, brake power (BP), and brake thermal efficiency (BTE) of the engine were determined. Gaseous emissions from the engine’s combustion were characterized using the BOSEAN BH-4S portable multi-gas detector, while the organic emissions compositions were detected and quantified using Gas Chromatography-Mass Spectrometry (GC-MS). The fuel properties of SBOB and its blends were found to be within the range of acceptable standards. However, the carbon content, sulphur content, heating value, and ash content of the blends decreased from 0.68 to 0.12 wt %, 0.04 to 0.00 wt %, 44.2 to 34.2 MJ/kg, and 0.020 to 0.010 wt %, respectively. The engine torque, brake power, BTE, and engine vibrations were found to reduce when the biodiesel blends were used. Besides the diesel fuel, the biodiesel blend, B25, produced the best engine performance characteristics with 8.50 Nm torque, 1780.95 W BP, and 90.29% BTE. The B100 produced the lowest concentrations of carbon emissions, viz. 520 ppm CO and 1.0% CO2. The NO and NO2 concentrations were found to increase for all the biodiesel blends used. The NO and NO2 concentrations were measured as 230 ppm and 210 ppm for B0, respectively, and 250 ppm and 235 ppm for B25, respectively. The research showed that SBOB has improved engine performance and lowered the emissions profile of CO and CO2 compared with petroleum diesel. The GCMS analysis confirmed that some harmful organic compounds were present in the emissions profile obtained from the exhaust samples of the diesel engine at various compositions.

23 January 2016 in Journal of Materials Science: Materials in Electronics
Verified
Journal Article
Closed access
PDF file
MDMondiu Durowoju
Mondiu Durowoju
Rotimi SadikuRotimi Sadiku
Rotimi Sadiku
SDS. Diouf
S. Diouf
MSM. B. Shongwe
M. B. Shongwe
POP. A. Olubambi
P. A. Olubambi
MRMunyadziwa Mercy Ramakokovhu
Munyadziwa Mercy Ramakokovhu

22 February 2020 in SN Applied Sciences
Verified
Journal Article
Open access
PDF file
EOE. O. Olawuni
E. O. Olawuni
MDMondiu Durowoju
Mondiu Durowoju
TAT. B. Asafa
T. B. Asafa
Aluminium metal matrix composites have gained a lot of attention because of their outstanding properties making them useful for aerospace, automobile and marine applications. Composites are replacing metals as structural materials, and a detailed study of the relationship between hardness and Young’s modulus becomes essential. In this paper, the correlation between hardness and elastic modulus of discarded aluminum pistons reinforced with zirconium diboride and snail shells is presented. The theoretical hardness was determined from the ratio of indentation hardness to indentation modulus while elastic modulus was evaluated based on composite equation. The results indicated that hardness and elastic modulus increased with the weight percentage of the composites while the resistance to plastic deformation H3/E2 increased with H. The wide discrepancy between the theoretical and experimental Young’s modulus is attributed to the fact that theoretical elastic moduli were obtained from perfect/single crystal materials while experimental values are obtained from polycrystalline/imperfect crystals. The calculated Young’s moduli obtained through mixture rule range from 64 to 92 GPa which are higher than 69 GPa of aluminium alloy. It is therefore evident that the composite materials can be used for engineering applications.