Austin Fleming

Dr. Austin Fleming


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 July 2016 in Applied Physics Letters
Verified
Journal Article
Closed access
NHNicolas Horny
Nicolas Horny
MCMihai Chirtoc
Mihai Chirtoc
Austin FlemingAustin Fleming
Austin Fleming
GHGeorges Hamaoui
Georges Hamaoui
HBHeng Ban
Heng Ban
Kapitza thermal resistance is determined using high-frequency photothermal radiometry (PTR) extended for modulation up to 10 MHz. Interfaces between 50 nm thick titanium coatings and silicon or stainless steel substrates are studied. In the used configuration, the PTR signal is not sensitive to the thermal conductivity of the film nor to its optical absorption coefficient, thus the Kapitza resistance is directly determined from single thermal parameter fits. Results of thermal resistances show the significant influence of the nature of the substrate, as well as of the presence of free electrons at the interface.

27 July 2018 in Scientific Reports
Verified
Journal Article
Open access
PDF file
GHGeorges Hamaoui
Georges Hamaoui
NHNicolas Horny
Nicolas Horny
ZHZilong Hua
Zilong Hua
TZTianqi Zhu
Tianqi Zhu
JRJean-François Robillard
Jean-François Robillard
MCMihai Chirtoc
Mihai Chirtoc
This work presents a direct measurement of the Kapitza thermal boundary resistance Rth, between platinum-silicon and platinum silicide-silicon interfaces. Experimental measurements were made using a frequency domain photothermal radiometry set up at room temperature. The studied samples consist of ≈50 nm of platinum and ≈110 nm of platinum silicide on silicon substrates with different doping levels. The substrate thermal diffusivity was found via a hybrid frequency/spatial domain thermoreflectance set up. The films and the interfaces between the two layers were characterized using scanning electron microscopy, transmission electron microscopy and energy-dispersive X-ray spectroscopy. X-ray diffraction was also used to determine the atomic and molecular structures of the samples. The results display an effect of the annealing process on the Kapitza resistance and on the thermal diffusivities of the coatings, related to material and interface changes. The influence of the substrate doping levels on the Kapitza resistance is studied to check the correlation between the Schottky barrier and the interfacial heat conduction. It is suggested that the presence of charge carriers in silicon may create new channels for heat conduction at the interface, with an efficiency depending on the difference between the metal’s and substrate’s work functions.

1 October 2017 in Synthetic Metals
Verified
Journal Article
Closed access
DTDominika Trefon-Radziejewska
Dominika Trefon-Radziejewska
JJJustyna Juszczyk
Justyna Juszczyk
Austin FlemingAustin Fleming
Austin Fleming
NHNicolas Horny
Nicolas Horny
JAJean Stéphane Antoniow
Jean Stéphane Antoniow
Jerzy BodzentaJerzy Bodzenta
Jerzy Bodzenta

31 May 2016 in International Journal of Thermophysics
Verified
Journal Article
Open access
PDF file
Jerzy BodzentaJerzy Bodzenta
Jerzy Bodzenta
JJJustyna Juszczyk
Justyna Juszczyk
AKAnna Kaźmierczak-Bałata
Anna Kaźmierczak-Bałata
PFPiotr Firek
Piotr Firek
Austin FlemingAustin Fleming
Austin Fleming
MCMihai Chirtoc
Mihai Chirtoc
Quantitative thermal measurements with spatial resolution allowing the examination of objects of submicron dimensions are still a challenging task. The quantity of methods providing spatial resolution better than 100 nm is very limited. One of them is scanning thermal microscopy (SThM). This method is a variant of atomic force microscopy which uses a probe equipped with a temperature sensor near the apex. Depending on the sensor current, either the temperature or the thermal conductivity distribution at the sample surface can be measured. However, like all microscopy methods, the SThM gives only qualitative information. Quantitative measuring methods using SThM equipment are still under development. In this paper, a method based on simultaneous registration of the static and the dynamic electrical resistances of the probe driven by the sum of dc and ac currents, and examples of its applications are described. Special attention is paid to the investigation of thin films deposited on thick substrates. The influence of substrate thermal properties on the measured signal and its dependence on thin film thermal conductivity and film thickness are analyzed. It is shown that in the case where layer thicknesses are comparable or smaller than the probe–sample contact diameter, a correction procedure is required to obtain actual thermal conductivity of the layer. Experimental results obtained for thin SiO\(_{\mathrm {2}}\) and BaTiO\(_{\mathrm {3 }}\)layers with thicknesses in the range from 11 nm to 100 nm are correctly confirmed with this approach.

15 June 2021 in Sensors
Verified
Journal Article
Open access
PDF file
Sohel RanaSohel Rana
Sohel Rana
Harish SubbaramanHarish Subbaraman
Harish Subbaraman
Austin FlemingAustin Fleming
Austin Fleming
NKNirmala Kandadai
Nirmala Kandadai
Optical fiber sensors (OFS) are a potential candidate for monitoring physical parameters in nuclear environments. However, under an irradiation field the optical response of the OFS is modified via three primary mechanisms: (i) radiation-induced attenuation (RIA), (ii) radiation-induced emission (RIE), and (iii) radiation-induced compaction (RIC). For resonance-based sensors, RIC plays a significant role in modifying their performance characteristics. In this paper, we numerically investigate independently the effects of RIC and RIA on three types of OFS widely considered for radiation environments: fiber Bragg grating (FBG), long-period grating (LPG), and Fabry-Perot (F-P) sensors. In our RIC modeling, experimentally calculated refractive index (RI) changes due to low-dose radiation are extrapolated using a power law to calculate density changes at high doses. The changes in RI and length are subsequently calculated using the Lorentz–Lorenz relation and an established empirical equation, respectively. The effects of both the change in the RI and length contraction on OFS are modeled for both low and high doses using FIMMWAVE, a commercially available vectorial mode solver. An in-depth understanding of how radiation affects OFS may reveal various potential OFS applications in several types of radiation environments, such as nuclear reactors or in space.

1 March 2019 in International Journal of Heat and Mass Transfer
Verified
Journal Article
Closed access
ZHZilong Hua
Zilong Hua
Austin FlemingAustin Fleming
Austin Fleming
HBHeng Ban
Heng Ban