Robert Kühne

Mr. Robert Kühne


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 April 2021 in Coatings
Verified
Journal Article
Open access
PDF file
NBNina Baule
Nina Baule
YKYoungSuk Kim
YoungSuk Kim
AZAndré T. Zeuner
André T. Zeuner
LHLars Haubold
Lars Haubold
RKRobert Kühne
Robert Kühne
Qi Hua FanQi Hua Fan
Qi Hua Fan
This work discusses a study on a surface treatment for creating extremely durable low-friction, wear and corrosion-resistant surfaces for tribological components in harsh conditions. A duplex surface treatment was developed that combines the advantages of ultra-fast electrochemical boriding with those of hard tetrahedral amorphous carbon coatings. The friction and wear properties of the duplex treatment are compared to the boride-only treatment of AISI 1045 steel, while corrosion and contact fatigue behaviors of the duplex layer are compared to that of the single-layer carbon coating on low carbon steel. The duplex treatment yields wear rates as low as 6 × 10−8 mm3·N−1·m−1 and a coefficient of friction of 0.14 when tested against a steel counter face. The contact fatigue impact tests reveal that the high hardness of 1200 HV0.05 of the borided layer in the duplex treatment leads to higher resistance against indentation but is accompanied by a higher incidence of crack initiation, being in good agreement with the finite-element modeling of nanoindentation results. The duplex coatings exhibit resistance to pinhole corrosion as evidenced by a 3 h exposure to 15% HCl at room temperature.

25 August 2025 in Applied Sciences
Verified
Journal Article
Open access
PDF file
KFKim Feldhoff
Kim Feldhoff
HWHajo Wiemer
Hajo Wiemer
PTPhilip Träger
Philip Träger
RKRobert Kühne
Robert Kühne
Martina ZimmermannMartina Zimmermann
Martina Zimmermann
SISteffen Ihlenfeldt
Steffen Ihlenfeldt
A systematic literature review is fundamental to building a robust research foundation, informing experimental methodology, and ensuring the quality of future scientific output. However, manual extraction of targeted information from scientific publications is often laborious and prone to error, especially when researchers require rapid access to relevant findings without specialized hardware. This paper introduces an automated workflow for information extraction from scientific publications in the engineering domain. The proposed workflow consists of two primary stages: data preparation and information extraction. During data preparation, PDF files are converted to plain text and segmented into logical sections using a rule-based block detection and classification algorithm for keeping semantics. Information extraction is then performed by applying regular expressions both on keys and values in the same sentence to identify and extract relevant process and material data from the segmented text. The approach was evaluated on a dataset of 18 open-access scientific publications from various journals and conference proceedings in the AM domain. The results of the automated extraction were compared with manual extraction and with a modern large language model (LLM)-based approach. The findings demonstrate that the proposed workflow can accurately and efficiently extract relevant process and material data, achieving competitive performance relative to the LLM-based method. The workflow offers a significant reduction in time and potential errors associated with manual extraction, with automated processing averaging 15 s per document compared to one hour for manual extraction, and achieving a 76% match rate. This efficiency enables researchers to rapidly and effectively extract data. The methodology is readily transferable to other scientific fields where systematic literature reviews and structured data extraction are required.

19 January 2023 in Metals
Verified
Journal Article
Open access
PDF file
AZAndré Till Zeuner
André Till Zeuner
TWThomas Wanski
Thomas Wanski
SSSebastian Schettler
Sebastian Schettler
JFJonas Fell
Jonas Fell
AWAndreas Wetzig
Andreas Wetzig
Martina ZimmermannMartina Zimmermann
Martina Zimmermann
Laser cutting is a suitable manufacturing method for generating complex geometries for sheet metal components. However, their cyclic load capacity is reduced compared to, for example, milled components. This is due to the influence of the laser-cut edge, whose characteristic features act as crack initiation sites, especially resolidified material in the form of burr and melt droplets. Since sheet metal components are often formed into their final geometry after cutting, another important factor influencing fatigue behavior is the effect of the forming process on the laser-cut edge. In particular, the effect of high degrees of deformation has not yet been researched in detail. Accordingly, sheets of AISI 304 were processed by laser cutting and pre-deformed. In the process, α’-martensite content was set to be comparable despite different degrees of deformation. It was found that deformation to high elongations caused a large part of the melt adhesions to fall off, but those still attaching were partially detached and thus formed an initial notch for crack initiation. This significantly lowered the fatigue strength.

20 December 2021 in Metals
Verified
Journal Article
Open access
PDF file
AZAndré Till Zeuner
André Till Zeuner
RKRobert Kühne
Robert Kühne
CSChristiane Standke
Christiane Standke
DKDavid Köberlin
David Köberlin
TWThomas Wanski
Thomas Wanski
Martina ZimmermannMartina Zimmermann
Martina Zimmermann
Laser cutting is used in the production of formed sheet metal components. However, the cyclic load capacity is reduced compared to other subtractive processes. Laser cutting results in a significant loss of fatigue strength; however, thermal joining has its own effect on the cyclic load capacity. Accordingly, brazing causes a significant reduction in the mechanical strength. However, the open question is what consequences a combination of both processes may have on the overall fatigue strength of sheet metals. Laser-cut samples of AISI 304 with and without a brazed-on element were investigated for their microstructure and mechanical properties. The brazing process was found to have an annealing effect on the microstructure. It was further observed that the fatigue behavior of brazed specimens is dominated by inhomogeneities at the surface of the filler metal fillet located in the geometric notch of the brazed joint. Fatigue strength decreased by almost 50% compared to as-cut specimens. As long as no shared diffusion zone is formed between the laser-cut and the brazed joint, the use of laser cutting for the production of such components appears to be reasonable and does not further contribute to the loss of cyclic strength.