Large bone defects are commonly treated by replacement with auto- and allografts, which have substantial drawbacks including limited supply, donor site morbidity, and possible tissue rejection. This study aimed to improve bone defect treatment using a custom-made filament for tissue engineering scaffolds. The filament consists of biodegradable polylactide acid (PLA) and a varying amount (up to 20%) of osteoconductive S53P4 bioglass. By employing an innovative, additive manufacturing technique, scaffolds with optimized physico-mechanical and biological properties were produced. The scaffolds feature adjustable macro- and microporosity (200–2000 µm) with adaptable mechanical properties (83–135 MPa). Additionally, controllable calcium release kinetics (0–0.25 nMol/µL after 24 h), tunable mesenchymal stem cell (MSC) adhesion potential (after 24 h by a factor of 14), and proliferation (after 168 h by a factor of 18) were attained. Microgrooves resulting from the 3D-printing process on the surface act as a nucleus for cell aggregation, thus being a potential cell niche for spheroid formation or possible cell guidance. The scaffold design with its adjustable biomechanics and the bioglass with its antimicrobial properties are of particular importance for the preclinical translation of the results. This study comprehensibly demonstrates the potential of a 3D-printed bioglass composite scaffold for the treatment of critical-sized bone defects.

In Bone Tissue Engineering (BTE), autologous bone-regenerative cells are combined with a scaffold for large bone defect treatment (LBDT). Microporous, polylactic acid (PLA) scaffolds showed good healing results in small animals. However, transfer to large animal models is not easily achieved simply by upscaling the design. Increasing diffusion distances have a negative impact on cell survival and nutrition supply, leading to cell death and ultimately implant failure. Here, a novel scaffold architecture was designed to meet all requirements for an advanced bone substitute. Biofunctional, porous subunits in a load-bearing, compression-resistant frame structure characterize this approach. An open, macro- and microporous internal architecture (100 µm–2 mm pores) optimizes conditions for oxygen and nutrient supply to the implant’s inner areas by diffusion. A prototype was 3D-printed applying Fused Filament Fabrication using PLA. After incubation with Saos-2 (Sarcoma osteogenic) cells for 14 days, cell morphology, cell distribution, cell survival (fluorescence microscopy and LDH-based cytotoxicity assay), metabolic activity (MTT test), and osteogenic gene expression were determined. The adherent cells showed colonization properties, proliferation potential, and osteogenic differentiation. The innovative design, with its porous structure, is a promising matrix for cell settlement and proliferation. The modular design allows easy upscaling and offers a solution for LBDT.

Three-dimensional printing, especially fused filament fabrication (FFF), offers great possibilities in (bio-)medical applications, but a major downside is the difficulty in sterilizing the produced parts. This study evaluates the questions of whether autoclaving is a possible solution for FFF-printed parts and if the printer itself could be seen as an inherent sterilization method. In a first step, an investigation was performed on the deformation of cylindrically shaped test parts after running them through the autoclaving process. Furthermore, the inherent sterility possibilities of the printing process itself were evaluated using culture medium sterility tests. It could be shown that, depending on the needed accuracy, parts down to a diameter of 5–10 mm can still be sterilized using autoclaving, while finer parts suffer from major deformations. For these, inherent sterilization of the printer itself is an option. During the printing process, over a certain contact time, heat at a higher level than that used in autoclaving is applied to the printed parts. The contact time, depending on the printing parameters, is calculated using the established formula. The results show that for stronger parts, autoclaving offers a cheap and good option for sterilization after FFF-printing. However, the inherent sterility possibilities of the printer itself can be considered, especially when printing with small layer heights for finer parts.

Epoxyeicosatrienoic acids (EET) facilitate regeneration in different tissues, and their benefit in dermal wound healing has been proven under normal conditions. In this study, we investigated the effect of 11,12 EET on dermal wound healing in diabetes. We induced diabetes by i.p. injection of streptozotocin 2 weeks prior to wound creation on the dorsal side of the mouse ear. 11,12 EET was applied every second day on the wound, whereas the control groups received only solvent. Epithelialization was monitored every second day intravitally up to wound closure. Wounds were stained for VEGF, CD31, TGF-β, TNF-α, SDF-1α, NF-κB, and Ki-67, and fibroblasts were counted after hematoxylin-eosin stain on days 3, 6, 9, and 16 after wounding. After induction of diabetes, wounds closed on day 13.00 ± 2.20 standard deviation (SD). Local 11,12 ETT application improved wound closure significantly to day 8.40 ± 1.39 SD. EET treatment enhanced VEGF and CD31 expression in wounds on day 3. It also seemed to raise TNF-α level on all days investigated as well as TGF-β level on days 3 and 6. A decrease in NF-κB could be observed on days 9 and 16 after EET application. The latter findings were not significant. SDF-1α expression was not influenced by EET application, and Ki-67 was significantly less in the EET group on day 9 after EET application. The number of fibroblasts was significantly increased on day 9 after the 11,12 EET application. 11,12 EET improve deteriorated wound healing in diabetes by enhancing neoangiogenesis, especially in the early phase of wound healing. Furthermore, they contribute to the dissolution of the initial inflammatory reaction, allowing the crucial transition from the inflammatory to proliferative phase in wound healing.

Introduction: In an emergency department, the majority of pediatric trauma patients present because of minor injuries. The aim of this study was to evaluate temporal changes in age-related injury pattern, trauma mechanism, and surgeries in pediatric patients. Methods: This retrospective study included patients < 18 years of age following trauma from 01/2009 to 12/2018 at a level I trauma center. They were divided into two groups: group A (A: 01/2009 to 12/2013) and group B (B: 01/2014 to 12/2018). Injury mechanism, injury pattern, and surgeries were analyzed. As major injuries fractures, dislocations, and organ injuries and as minor injuries contusions and superficial wounds were defined. Results: 23,582 patients were included (58% male, median age 8.2 years). There was a slight increase in patients comparing A (n = 11,557) and B (n = 12,025) with no difference concerning demographic characteristics. Significant more patients (A: 1.9%; B: 2.4%) were admitted to resuscitation room, though the number of multiple injured patients was not significantly different. In A (25.5%), major injuries occurred significantly less frequently than in B (27.0%), minor injuries occurred equally. Extremity fractures were significantly more frequent in B (21.5%) than in A (20.2%), peaking at 8–12 years. Most trauma mechanisms of both groups were constant, with a rising of sport injuries at 8–12 years. Conclusion: Although number of patients increases only slightly over a decade, there was a clear increase in major injuries, particularly extremity fractures, peaking at 8–12 years. At this age also sport accidents significantly increased. At least, admittance to resuscitation room rose but without an increase of multiple injured patients.