Hussam Mohammad

Mr. Hussam Mohammad

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 January 2022 in Polymers
Verified
Journal Article
Open access
PDF file
HMHussam Mohammad
Hussam Mohammad
ASAndrey Stepashkin
Andrey Stepashkin
Victor TcherdyntsevVictor Tcherdyntsev
Victor Tcherdyntsev
The goal of this study was to create a high-filled composite material based on polysulfone using various graphite materials. Composite material based on graphite-filled polysulfone was prepared using a solution method which allows the achievement of a high content of fillers up to 70 wt.%. Alongside the analysis of the morphology and structure, the thermal conductivity and mechanical properties of the composites obtained were studied. Structural analysis shows how the type of filler affects the structure of the composites with the appearance of pores in all samples which also has a noticeable effect on composites’ properties. In terms of thermal conductivity, the results show that using natural graphite as a filler gives the best results in thermal conductivity compared to artificial and expanded graphite, with the reduction of thermal conductivity while increasing temperature. Flexural tests show that using artificial graphite as a filler gives the composite material the best mechanical load transfer compared to natural or expanded graphite.

22 January 2023 in Polymers
Verified
Journal Article
Open access
PDF file
ASAndrey Stepashkin
Andrey Stepashkin
HMHussam Mohammad
Hussam Mohammad
EMElena Makarova
Elena Makarova
YOYulia V. Odintsova
Yulia V. Odintsova
ALAlexander I. Laptev
Alexander I. Laptev
Victor TcherdyntsevVictor Tcherdyntsev
Victor Tcherdyntsev
Tensile deformation behavior of continuous high-strength and high-modulus single carbon fibers impregnated with a polysulfone solution was investigated. The effect of the carbon fiber type, mass fraction of the polymer, and the loading rate on the tensile strength was studied. It was observed that, whereas for high-modulus carbon fibers the magnitude of tensile strength depends significantly on the loading rate, for high-strength carbon fibers, such dependence was nearly not observed. SEM study shows that at low loading rates, elementary filaments inside the impregnated fiber are able to align themselves along the load application axis because a thermoplastic matrix can flow under the tensile stresses’ force. As a result, the fiber’s strength properties can be realized more effectively in the thermoplastic-based composites than in the same composite with an epoxy matrix.

30 December 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
HMHussam Mohammad
Hussam Mohammad
ASAndrey Stepashkin
Andrey Stepashkin
ALAlexander I. Laptev
Alexander I. Laptev
Victor TcherdyntsevVictor Tcherdyntsev
Victor Tcherdyntsev
Polysulfone-based composite materials filled with artificial, natural, or thermally expanded graphite have been investigated. Composite materials with filling degrees between 30 and 70 wt.% were prepared using solution technology. High filling levels with graphite fillers allowed for the achievement of thermal conductivity of 7.35 W/m · K and electrical conductivity of 52.9 S/cm. The use of natural graphite has been found to have the greatest impact on thermal and electrical characteristics, while materials with dispersed artificial graphite exhibit the best mechanical properties. Evolution of samples’ density and porosity with the filling degree as well as the effect of these parameters on the conductive properties have been analyzed and discussed.

11 October 2023 in Alexandria Engineering Journal
Verified
Journal Article
Open access
ASAndrey Stepashkin
Andrey Stepashkin
SCSuresh Chavhan
Suresh Chavhan
SGS.V. Gromov
S.V. Gromov
AKAshish Khanna
Ashish Khanna
VTV.V. Tcherdyntsev
V.V. Tcherdyntsev
SAS.S. Alexandrova
S.S. Alexandrova

25 March 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
HMHussam Mohammad
Hussam Mohammad
ASAndrey Stepashkin
Andrey Stepashkin
Victor TcherdyntsevVictor Tcherdyntsev
Victor Tcherdyntsev
Composites based on polysulfone materials filled with various types of graphite and carbon black were studied and a solution technique was used to create composite materials with filling degrees ranging from 30 to 70% by weight. High filling levels with graphite fillers enabled thermal conductivity of 17.4 W/m·K to be achieved. The addition of carbon black as a filler to the composite helped to improve its mechanical characteristics, and its influence on electrical and thermal conductivity has also been explored. Natural graphite provides the best effect on composite thermal and electrical properties, whereas using artificial graphite allows to improve the mechanical behavior of composites. The relationship between sample density, porosity, and composition, as well as the effect of these factors on composite conductivity, has been studied and addressed.

2 December 2024 in Preprints.org
Verified
Preprint
Open access
PDF file
ASAndrey Stepashkin
Andrey Stepashkin
LOLeonid Olifirov
Leonid Olifirov
HMHussam Mohammad
Hussam Mohammad
EMElena Makarova
Elena Makarova
Victor TcherdyntsevVictor Tcherdyntsev
Victor Tcherdyntsev
The deformation features of a thermoplastic matrix under long-term and cyclic loads have not yet received the necessary broad coverage. The evolution of deformations and accumulation of tensile damage in polysulfone reinforced with unidirectional high-strength and high-modulus carbon fiber threads under long-term and cyclic loads are studied. Composites were prepared by im-pregnating carbon fibers with a polysulfone solution and then removing the solvent. Stress re-laxation, creep, and low-cycle fatigue, as well as the structure and nature of damage to materials under load, are studied. The dependence of the effective modulus of elasticity on the maximum applied stresses is studied. It is shown that in composite materials with a thermoplastic matrix, the tensile diagrams are nonlinear, and the effective modulus of elasticity increases with increasing stress. Poisson's ratio at the initial moment is close to those for the pure polymer and is about 0.40, whereas with increasing stress this value decreases to 0.19-0.22. Video processing of sample de-formation in combination with scanning electron microscopy allows us to evaluate local features of deformation processes in carbon fibers and identify the main patterns of damage accumulation processes under long-term and cyclic loads.