A simplified design of an inline transition between microstrip and rectangular waveguide is presented in this paper. The transition makes use of a dielectric filled rectangular waveguide (DFRW) as an intermediate step, which simplifies manufacturing and allows for an analytical design. The behavior of the transition has been experimentally validated in the W-band by means of a back-to-back configuration. Good performance has been achieved: a return loss greaterthan 10 dB and mean insertion loss lower than 1 dB.
28 May 2020 in IEEE Transactions on Antennas and Propagation
In this paper, three compact antennas using the Ridge Gap Waveguide (RGW) technology working in the millimeter-wave band (60 GHz), with a high-purity and broadband circular polarization (CP) are numerically and experimentally analyzed. The structure is fed from the bottom by means of a standard WR-15 waveguide (V-band) to make it compatible with standard measurement systems. It is coupled with a miniaturized step transition to a ridgeline that ends in two arms of different lengths. CP is generated in a simple and effective way, by means of two orthogonal feeder arms that excite a CP in a diamond-shaped slot on top. Simulations and measurements have an excellent agreement reaching a matching bandwidth (S11 < 10 dB) from 60.3 to 69.6 GHz (>. Applying the axial ratio criterion (AR < 3 dB) the bandwidth in CP is 14.48%, with respect to the central frequency (59 to 70 GHz). The maximum gain is obtained with the most evolved design incorporating a diamond aperture with a horn taper and a circular groove, reaching a value of 11.12 dB at 67.3 GHz.
In this paper two different simple to design and easy to manufacturing transitions from a microstrip to rectangular waveguide based on ridge and groove gap waveguides are studied. The first one is based on a combination of a groove and ridge gap waveguide. In this case, the microstrip substrate occupies the whole bottom metallic housing block, namely, the transition and the gap between the bed of nails and the lid; therefore, it does not require any substrate shaping. Nevertheless, the transition needs to replace groove waveguide by ridge gap waveguide sections to avoid higher-order mode excitation. In the second approach, based on only a groove gap waveguide, the substrate is shaped to be only in the microstrip section, that is, outside the bed of nails area. This leads to a simplification of the design procedure. Prototypes of both transitions have been characterized, showing good agreement with the simulations taking into account the manufacturing tolerances. Performance comparable to the state-of-the-art in this frequency band has been achieved.
1 September 2020 in IEEE Transactions on Terahertz Science and Technology
This paper presents a planar silicon integrated subharmonic mixer on top of a photonic-crystal platform. The local oscillator (LO) power is injected through a 2D photonic-crystal (PC) slab to a resonant cavity that effectively couples the signal to a planar bow-tie antenna. The same antenna, which is printed on the top of the PC cavity, contains an antiparallel Schottky diode pair which performs the down-conversion. The proposed design is a single layer, low cost, low profile device. Moreover, the described fabrication process is compatible with active components integration. The performance of the design has been experimentally demonstrated showing good agreement with the simulation and is comparable with the state-of-the-art of planar mixers. The work presented here is based on concepts and technologies from electronics and photonics domains and may be a good starting point for the creation of new devices, allowing the integration and upgrading of existing techniques from both worlds.
In this paper we present a microstrip patch excitation technique through electromagnetical coupling in a single layer able to generate broadband circularly polarized (CP) radiation. The circular polarization operation is obtained by simply adjusting the feed system dimensions without modifying the microstrip radiator. The proposed feed technique also has the advantage of being applicable to any regular polygon; in this case, its operation is validated experimentally for a square and an ellipse. From the simulation results a 3-dB axial-ratio bandwidth of 100 MHz (4%) and 110MHz (4.48%) are obtained, respectively, relative to the center frequency of 2.44 GHz, making the designed antennas an interesting solution for applications such as RFID readers, or communications in ISM band.
1 December 2015 in AEU - International Journal of Electronics and Communications