The influence of ultra-short laser modification on the surface morphology and possible chemical alteration of poly-lactic acid (PLA) matrix in respect to the optimization of cellular and antibacterial behavior were investigated in this study. Scanning electron microscopy (SEM) morphological examination of the processed PLA surface showed the formation of diverse hierarchical surface microstructures, generated by irradiation with a range of laser fluences (F) and scanning velocities (V) values. By controlling the laser parameters, diverse surface roughness can be achieved, thus influencing cellular dynamics. This surface feedback can be applied to finely tune and control diverse biomaterial surface properties like wettability, reflectivity, and biomimetics. The triggering of thermal effects, leading to the ejection of material with subsequent solidification and formation of raised rims and 3D-like hollow structures along the processed zones, demonstrated a direct correlation to the wettability of the PLA. A transition from superhydrophobic (θ > 150°) to super hydrophilic (θ < 20°) surfaces can be achieved by the creation of grooves with V = 0.6 mm/s, F = 1.7 J/cm². The achieved hierarchical architecture affected morphology and thickness of the processed samples which were linked to the nature of ultra-short laser-material interaction effects, namely the precipitation of temperature distribution during material processing can be strongly minimized with ultrashort pulses leading to non-thermal and spatially localized effects that can facilitate volume ablation without collateral thermal damage The obtained modification zones were analyzed employing Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS), Energy dispersive X-ray analysis (EDX), and optical profilometer. The modification of the PLA surface resulted in an increased roughness value for treatment with lower velocities (V = 0.6 mm/s). Thus, the substrate gains a 3D-like architecture and forms a natural matrix by microprocessing with V = 0.6 mm/s, F = 1.7 J/cm², and V = 3.8 mm/s, F = 0.8 J/cm². The tests performed with Mesenchymal stem cells (MSCs) demonstrated that the ultra-short laser surface modification altered the cell orientation and promoted cell growth. The topographical design was tested also for the effectiveness of bacterial attachment concerning chosen parameters for the creation of an array with defined geometrical patterns.

Developing antimicrobial surfaces that combat implant-associated infections while promoting host cell response is a key strategy for improving current therapies for orthopaedic injuries. In this paper, we present the application of ultra-short laser irradiation for patterning the surface of a 3D biodegradable synthetic polymer in order to affect the adhesion and proliferation of bone cells and reject bacterial cells. The surfaces of 3D-printed polycaprolactone (PCL) scaffolds were processed with a femtosecond laser (λ = 800 nm; τ = 130 fs) for the production of patterns resembling microchannels or microprotrusions. MG63 osteoblastic cells, as well as S. aureus and E. coli, were cultured on fs-laser-treated samples. Their attachment, proliferation, and metabolic activity were monitored via colorimetric assays and scanning electron microscopy. The microchannels improved the wettability, stimulating the attachment, spreading, and proliferation of osteoblastic cells. The same topography induced cell-pattern orientation and promoted the expression of alkaline phosphatase in cells growing in an osteogenic medium. The microchannels exerted an inhibitory effect on S. aureus as after 48 h cells appeared shrunk and disrupted. In comparison, E. coli formed an abundant biofilm over both the laser-treated and control samples; however, the film was dense and adhesive on the control PCL but unattached over the microchannels.

The increasing prevalence of orthopedic disorders and technological advances have significantly improved the design and functionality of orthopedic implants, fostering the growth of the orthopedic implant market. Polyetheretherketone (PEEK) has emerged as a promising alternative to the gold standard of metallic implants due to its favorable biocompatibility and mechanical properties, comparable to those of bone tissue. However, its chemical inertness results in poor osseointegration. This study investigates femtosecond (fs) laser-induced micro- and nanoscale surface modifications of PEEK, aiming to develop surface modifications potentially favorable for bioactivity enhancement of the as-created transient cellular scaffolds. Various texturing designs were fabricated by precisely controlling the laser parameters applied (laser beam power P = 20–80 mW, hatch spacing dx = 45–100 µm, scanning velocity V = 3.44–32 mm/s). The resulting morphologies were characterized by SEM, EDX, XRD, micro-Raman, 3D profilometry, water contact angle measurements, and evaluated for preliminary biological response. The main achievement of the research indicates that the hierarchical topography created by fs laser microprocessing significantly increased surface morphology, which may subsequently provide surface conditions supporting successful osseointegration. These findings demonstrate the feasibility of femtosecond laser structuring as a promising, reproducible, and environmentally friendly method for sustainable surface biofunctionalization of PEEK in orthopedic applications.

Silk fibroin (SF), the primary protein in silkworm silk, has emerged as a promising organic nonlinear optical material due to its unique combination of optical transparency, biocompatibility, and environmental sustainability. In this study, we investigate the nonlinear optical properties of SF thin films using the z-scan technique with femtosecond laser pulses (35 fs, 800 nm, 1 kHz). Our results reveal a strong self-defocusing effect (negative nonlinear refractive index) and significant multiphoton absorption, demonstrating SF’s tunable nonlinear response. Additionally, optical transmittance measurements confirm SF’s partial transparency in the deep UV region, enhancing its potential for second-harmonic generation (SHG) and efficient light frequency conversion. These findings address a key knowledge gap in nonlinear optics, positioning SF as a versatile biopolymer for advanced photonic applications.

Ultra-short laser (USL)-induced surface structuring combined with nanoparticles synthesis by multiphoton photoreduction represents a novel single-step approach for commercially pure titanium (cp-Ti) surface enhancement. Such a combination leads to the formation of distinct topographical features covered by nanoparticles. The USL processing of cp-Ti in an aqueous solution of silver nitrate (AgNO₃) induces the formation of micron-sized spikes surmounted by silver nanoparticles (AgNPs). The proposed approach combines the structuring and oxidation of the Ti surface and the synthesis of AgNPs in a one-step process, without the use of additional chemicals or a complex apparatus. Such a process is easy to implement, versatile and sustainable compared to alternative methodologies capable of obtaining comparable results. Antimicrobial surfaces on medical devices (e.g., surgical tools or implants), for which titanium is widely used, can be realized due to the simultaneous presence of AgNPs and micro/nano-structured surface topography. The processed surfaces were examined by means of a scanning electron microscope (SEM), energy-dispersive X-ray spectroscopy (EDX), atomic force microscopy (AFM) and Raman spectroscopy. The surface morphology and the oxidation, quality and quantity of AgNPs were analyzed in relation to process parameters (laser scanning speed and AgNO₃ concentration), as well as the effect of AgNPs on the Raman signal of Titanium oxide.

The field of bone tissue engineering is steadily being improved by novel experimental approaches. Nevertheless, microbial adhesion after scaffold implantation remains a limitation that could lead to the impairment of the regeneration process, or scaffold rejection. The present study introduces a methodology that employs laser-based strategies for the development of antimicrobial interfaces on tricalcium phosphate–hydroxyapatite (TCP-HA) scaffolds. The outer surfaces of the ceramic scaffolds with inner porosity were structured using a femtosecond laser (λ = 800 nm; τ = 70 fs) for developing micropatterns and altering local surface roughness. The pulsed laser deposition of ZnO was used for the subsequent functionalization of both laser-structured and unmodified surfaces. The impact of the fs irradiation was investigated by Raman spectroscopy and X-ray diffraction. The effects of the ZnO-layered ceramic surfaces on initial bacterial adherence were assessed by culturing Staphylococcus aureus on both functionalized and non-functionalized scaffolds. Bacterial metabolic activity and morphology were monitored via the Resazurin assay and microscopic approaches. The presence of ZnO evidently decreased the metabolic activity of bacteria and led to impaired cell morphology. The results from this study have led to the conclusion that the combination of fs laser-structured surface topography and ZnO could yield a potential antimicrobial interface for implants in bone tissue engineering.