The application of dual phase (DP) steels has been increasing significantly in the automotive industry because of their high strength as well as good ductility, thus, cold formability. These steels are generally joined using conventional welding methods such as resistance spot welding and laser welding in the production of automotive parts. In recent years, several studies have been conducted to investigate the possibility of joining the advanced high-strength steels such as DP steels using the solid-state friction stir welding (FSW) method due to its advantages over conventional fusion joining methods such as metallurgical benefits, energy efficiency, and environmental friendliness. The aim of this study is to investigate the microstructure, hardness and tensile properties of friction stir welded DP 600 steel plates. Thus, 1.5 mm thick DP 600 steel plates were friction stir butt-welded by a tungsten carbide stirring tool consisting of a concave shoulder having a diameter of 14 mm and a conical pin (angle=30°) with a diameter and length of 5 mm and 1.25 mm, respectively. In the weld trials conducted, the tool was tilted 2° and the down-force of the tool was kept constant at 6 kN. The tool rotation and traverse speeds used in FSW trials were 1600 rpm and 170 mm.min-1, respectively. The microstructure of friction stir welded zone comprised of main martensite, bainite, and refined ferrite. The average hardness of the stir zone has increased to about 400 HV. The tensile specimens failed in the base plate away from the weld zone and tensile strength as high as that of the base plate was obtained from the welded specimens, i.e., about 640 MPa. However, the elongation of the welded plates was significantly reduced, i.e. about 55% of that of the base.
This study investigated the formability behavior of dual-phase (DP) steel subjected to friction stir process (FSP), using a miniaturized Erichsen test. The friction stir process yielded a refined microstructure, which consisted of lath martensite and fine ferrite, as a result of dynamic recrystallization (DRX) and phase transformation. Both yield and tensile strength were significantly increased via the grain refinement and increasing martensite fraction. Biaxial formability behavior of the friction stir processed sample exhibited a decline as the Erichsen index (EI) decreased from 2.7 mm to 2.2 mm. However, the required punch load (FEI) increased compatibly with the strength value after FSP. The grain refinement caused by FSP led to an improvement in the orange peel effect, defined as a negative effect of increased surface roughness after metal forming. The value of mean roughness in the free dome surface of the FSPed sample decreased from 4.90 μm to 2.62 μm. It can be concluded that the roughening with the orange peel effect on free surfaces of stretched metal can be eliminated by the friction stir process.
5 December 2022 in Superconductor Science and Technology
Lead-free SnIn solders are promising for superconducting magnet applications. However, their superconducting properties are not as good as lead solders. In order to improve the superconducting performance of the Sn–In solders, researchers have investigated the superconducting properties of ternary systems such as Sn–In–Bi for solder joints. In this study, powders of Pb, Nb, AgCu and grapheme nano pellets in the ratios of 0.5–5 wt% have been added into SnIn (35:65) to investigate their microstructural, thermal and superconducting properties. The added materials enhance the superconducting properties. We find that even low Pb additions show a dramatic improvement in superconducting properties, with an increase in both Tc and Jc values of up to 6.35 K and 1.47 × 104 A m−2, respectively. This shows that much lower Pb content superconducting solders can be effective and could be used to replace the PbBi solder commonly used with the superconducting properties Tc=8.4 K, HC2 = 1.77 T, HC = 0.0909 T.