A micropillar compression study with two different techniques was performed on proton-irradiated additively manufactured (AM) 316L stainless steels. The sample was irradiated at 360 °C using 2 MeV protons to 1.8 average displacement per atom (dpa) in the near-surface region. A comparison study with mechanical test and microstructure characterization was made between planar and cross-sectional pillars prepared from the irradiated surface. While a 2 MeV proton irradiation creates a relatively flat damage zone up to 12 µm, the dpa gradient by a factor of 2 leads to significant dpa uncertainty along the pillar height direction for the conventional planar technique. Cross-sectional pillars can significantly reduce such dpa uncertainty. From one single sample, three cross-sectional pillars were able to show dpa-dependent hardening. Furthermore, post-compression transmission electron microscopy allows the determination of the deformation mechanism of individual micropillars. Cross-sectional micropillar compression can be used to study radiation-induced mechanical property changes with better resolution and less data fluctuation.
Additive manufacturing techniques are being used more and more to perform the precise fabrication of engineering components with complex geometries. The heterogeneity of additively manufactured microstructures deteriorates the mechanical integrity of products. In this paper, we printed AISI 316L stainless steel using the additive manufacturing technique of laser metal deposition. Both single-phase and dual-phase substructures were formed in the grain interiors. Electron backscatter diffraction and energy-dispersive X-ray spectroscopy indicate that Si, Mo, S, Cr were enriched, while Fe was depleted along the substructure boundaries. In situ micro-compression testing was performed at room temperature along the [001] orientation. The dual-phase substructures exhibited lower yield strength and higher Young’s modulus compared with single-phase substructures. Our research provides a fundamental understanding of the relationship between the microstructure and mechanical properties of additively manufactured metallic materials. The results suggest that the uneven heat treatment in the printing process could have negative impacts on the mechanical properties due to elemental segregation.
Additively manufactured (AM) and wrought 316L stainless steels were irradiated with 2 MeV protons at 360 °C. Depth-resolved void swelling was quantified using cross-sectional transmission electron microscopy, with a safe-zone analysis applied to exclude near-surface and proton-range artifacts. The AM 316L exhibits significantly lower swelling than the wrought alloy. Swelling in the AM material is characterized by larger voids but a much lower void number density, whereas the wrought alloy develops smaller voids at a substantially higher density. The two alloys also display distinct dependences on local damage: in AM 316L, void size increases with local dpa while the void density remains nearly constant, whereas in wrought 316L, the void size is approximately constant and the void density increases with local dpa. These trends indicate that AM 316L has already entered a void growth-dominated regime, while wrought 316L remains in a void-nucleation-dominated regime. The reduced swelling in the AM alloy is attributed to more effective defect-recombination sinks and/or reduced vacancy mobility associated with the AM microstructure. These findings provide important insight for the evaluation and optimization of AM 316L alloys for nuclear industry applications.
Gallium oxide (Ga2O3) has emerged as a promising material for high-power and radiation-tolerant electronics due to its ultra-wide bandgap and excellent thermal stability. In this study, single-crystal β-Ga2O3 was exposed to neutron irradiation for periods up to 300 h to investigate its structural, chemical, electronic, and mechanical response. Post-irradiation examination revealed that the material maintained its monoclinic crystal structure, with no evidence of phase transformation, elemental segregation, or significant bandgap alteration. Atom probe tomography and energy-dispersive spectroscopy confirmed uniform elemental distributions of Ga, O, and Fe, while high-resolution electron energy-loss spectroscopy indicated negligible changes in the electronic structure. Nanoindentation measurements showed an increase in hardness after irradiation, suggesting the formation of irradiation-induced defects and associated radiation-hardening. These findings demonstrate that β-Ga2O3 can withstand low-dose neutron irradiation while preserving its microstructural, chemical, and electronic integrity, highlighting its potential for robust, high-performance devices in extreme radiation environments.