In this paper, we present research on a novel low-profile piezoelectric rotary motor with a triangle-shaped stator. The stator of the motor comprises three interconnected piezoelectric bimorph plates forming an equilateral triangle. Bimorph plates consist of a passive layer fabricated from stainless steel and four piezo ceramic plates glued to the upper and lower surfaces. Furthermore, spherical contacts are positioned on each bimorph plate at an offset from the plate’s center. Vibrations from the stator are induced by a single sawtooth-type electric signal while the frequency of the excitation signal is close to the resonant frequency of the second out-of-plane bending mode of the bimorph plate. The offset of the spherical contacts allows for a half-elliptical motion trajectory. By contrast, the forward and backward motion velocities of the contacts differ due to the asymmetrical excitation signal. The inertial principle of the motor and the angular motion of the rotor were obtained. Numerical and experimental investigations showed that the motor operates at a frequency of 21.18 kHz and achieves a maximum angular speed of 118 RPM at a voltage of 200 Vp-p. Additionally, an output torque of 18.3 mN·mm was obtained under the same voltage. The ratio between motor torque and weight is 36 mN·mm/g, while the ratio of angular speed and weight is 28.09 RPM/g.
The paper represents numerical and experimental investigations on a 5-DOF piezoelectric robot that can provide rotary and planar motions of the payload. The design of the robot is based on a single piezoelectric ring and a triangular-shaped passive layer made from stainless steel. Six semispherical contacts of alumina oxide were used as contact points for rotary and planar motions. Finally, the top electrode of the piezo ceramic ring was divided into six equal segments to control the 3-DOF angular and 2-DOF planar motions of the payload. Two harmonic signals of different frequencies are used to drive the piezoelectric robot. The robot operation is based on the excitation of the third radial vibration mode of the ring and the first bending mode of the trapezoidal-shaped cantilever. Motion control is performed by switching electric signals between the particular segments of the piezoelectric ring. A numerical investigation was performed to validate the operation principle of the robot and to analyze electrical and mechanical characteristics. Numerical investigations showed that the first bending mode of trapezoidal cantilevers and the third radial mode of the piezo ceramic ring were obtained at a frequency of 13.79 kHz and 95.75 kHz, respectively. Moreover, it was revealed that the coupling ratio between vibration amplitudes of passive and active segments is more than 4 times. The prototype of the piezoelectric robot was made and an experimental study was performed to validate the operating principle of the robot, as well as to investigate the dynamic characteristics. The investigation showed that the highest velocity of the planar motion is 22.3 mm/s while the maximum angular motion speed is 29.3 RPM when an excitation voltage of 200 Vp-p and payload of 25.1 g was applied.
This article presents a numerical and experimental investigation of a novel rod-shaped linear piezoelectric actuator that consists of a square cross-section-shaped rod with eight piezo ceramic plates and a cylindrical guidance rail. The rod has a hollow cut made with an offset from the longitudinal axis of the symmetry. A cylindrical guidance rail is placed on one side of the rod, while T-shaped clamping is formed on the opposite side. The slider is mounted on the rail and is moved along it. The actuator is compact, making it possible to mount it directly on a printed circuit board (PCB) or in another device with limited mounting space, restricted mass, or actuator footprint. The operation of the actuator is based on the excitation of the first longitudinal vibration mode of the rod that induces in-plane bending vibration of the nodal zone of the rod due to a hollowed cut asymmetrically placed in the central part of the actuator. The actuator is driven by two sawtooth waveform electric signals with the phase difference of π that allows exciting longitudinal deformations of the rod and controls the reverse motion of the slider. The results of numerical investigations confirmed the operation principle of the actuator at the frequency of 59.72 kHz. The maximum displacement amplitude of the guidance rail in the longitudinal direction reaches up to 152.9 μm while the voltage of 200 Vp-p was applied. An experimental investigation of the actuator was made, and a maximum linear speed of 45.6 mm/s and thrust force of 115.4 mN was achieved.
A novel five degrees of freedom (5-DOF) piezoelectric actuator is proposed and analyzed in this paper. The actuator can provide unlimited self-motion in the plane and angular positioning of the spherical payload. The actuator is composed of a cylindrical bronze frame and a piezo ceramic ring glued on top of the cylinder. The cylinder has three cut-outs used to form three supports. The top electrode of the piezo ceramic ring is divided into six equal sections. Three electrodes are used to control the direction of the planar motion, while the remaining three electrodes allow controlling angular motion. The planar motion of the actuator is induced by employing radial vibrations of the supports, while the rotational motion of the sphere is obtained when radial vibrations of the corresponding sections of the piezo ceramic ring are excited. The proposed design of the actuator allows reducing coupling between vibrations of the different segments and ensures the possibility to obtain 5-DOF motion. The piezoelectric actuator is excited using a single harmonic signal switched between electrodes via a digitally controlled switch box. The numerical and experimental studies of the actuator were performed, and the operating principle was validated. The maximum linear velocity of 19.8 mm/s and angular speed of 31.3 RPM were obtained when the payload of 55.68 g and excitation voltage of 200 Vp-p was applied.
This article represents a numerical and experimental investigation of a piezoelectric linear actuator with asymmetric design. The actuator is based on a square-shaped rod with asymmetrical cut and T-shaped clamping. The cylindrical rail, with slider, is on the opposite side of the T-shaped clamping. The low-volume and mass of piezoelectric actuator allows to mount it directly to printed circuit board (PCB). The actuator operation is based on the inertial stick – slip operation principle inducted by the first longitudinal vibration mode excited by two sawtooth signals with phase difference . Furthermore, the longitudinal vibration mode induces bending deformations of the rod, increasing the displacements of the cylindrical rail. The results of numerical and experimental investigations have validated the actuator operating principle, as well as shown that the displacement amplitudes of the guidance rail have reached 153.6 μm at the 200 V p-p excitation signal amplitude, while the linear motion speed reached 45.6 mm/s at the same excitation signal.
Results of numerical and experimental investigations of a novel inertial piezoelectric rotary type motor based on a low profile stator with trapezoidal waveguides. The proposed motor has a simple design and is well scalable. Moreover, the proposed design of the motor allows mount it on a printed circuit board and use it in a small-size mobile positioning and actuating systems. The structure of the stator is based on a square type hollowed steel frame with four straight trapezoidal waveguides that are used to transfer vibrations of the stator to the rotation of the rotor. Piezo ceramic plates are glued on both sides of the stator. The thickness of the assembled stator is 0.9 mm, while the total area needed for stator mounting does not exceed 625 mm2. The driving of the rotor is based on the stick-slip principle, which is induced by excitation of the second in-plane bending mode of the four bimorph plates applying two saw tooth waveform signals with a phase difference by π. The numerical and experimental investigation was carried out to validate the operation principle of the motor and to measure the mechanical and electrical characteristics. The maximum angular rotation speed of 1304 RPM was achieved at a resonance frequency of 44.81 kHz when a preload of a 7.35mN was applied.