David Eugen Grimm

Prof. Dr. David Eugen Grimm

orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 September 2022 in Sensors
Verified
Journal Article
Open access
PDF file
LSLadina Steiner
Ladina Steiner
GSGéraldine Studemann
Géraldine Studemann
DGDavid Eugen Grimm
David Eugen Grimm
CMChristoph Marty
Christoph Marty
SLSilvan Leinss
Silvan Leinss
Global navigation satellite system (GNSS) refractometry enables automated and continuous in situ snow water equivalent (SWE) observations. Such accurate and reliable in situ data are needed for calibration and validation of remote sensing data and could enhance snow hydrological monitoring and modeling. In contrast to previous studies which relied on post-processing with the highly sophisticated Bernese GNSS processing software, the feasibility of in situ SWE determination in post-processing and (near) real time using the open-source GNSS processing software RTKLIB and GNSS refractometry based on the biased coordinate Up component is investigated here. Available GNSS observations from a fixed, high-end GNSS refractometry snow monitoring setup in the Swiss Alps are reprocessed for the season 2016/17 to investigate the applicability of RTKLIB in post-processing. A fixed, low-cost setup provides continuous SWE estimates in near real time at a low cost for the complete 2021/22 season. Additionally, a mobile, (near) real-time and low-cost setup was designed and evaluated in March 2020. The fixed and mobile multi-frequency GNSS setups demonstrate the feasibility of (near) real-time SWE estimation using GNSS refractometry. Compared to state-of-the-art manual SWE observations, a mean relative bias below 5% is achieved for (near) real-time and post-processed SWE estimation using RTKLIB.

25 December 2021 in Remote Sensing
Verified
Journal Article
Open access
PDF file
UKUrsula Kälin
Ursula Kälin
LSLouis Staffa
Louis Staffa
DGDavid Eugen Grimm
David Eugen Grimm
AWAxel Wendt
Axel Wendt
To validate the accuracy and reliability of onboard sensors for object detection and localization for driver assistance, as well as autonomous driving applications under realistic conditions (indoors and outdoors), a novel tracking system is presented. This tracking system is developed to determine the position and orientation of a slow-moving vehicle during test maneuvers within a reference environment (e.g., car during parking maneuvers), independent of the onboard sensors. One requirement is a 6 degree of freedom (DoF) pose with position uncertainty below 5 mm (3σ), orientation uncertainty below 0.3° (3σ), at a frequency higher than 20 Hz, and with a latency smaller than 500 ms. To compare the results from the reference system with the vehicle’s onboard system, synchronization via a Precision Time Protocol (PTP) and system interoperability to a robot operating system (ROS) are achieved. The developed system combines motion capture cameras mounted in a 360° panorama view setup on the vehicle, measuring retroreflective markers distributed over the test site with known coordinates, while robotic total stations measure a prism on the vehicle. A point cloud of the test site serves as a digital twin of the environment, in which the movement of the vehicle is visualized. The results have shown that the fused measurements of these sensors complement each other, so that the accuracy requirements for the 6 DoF pose can be met while allowing a flexible installation in different environments.

13 December 2021 in Preprints.org
Verified
Preprint
Open access
UKUrsula Kälin
Ursula Kälin
LSLouis Staffa
Louis Staffa
DGDavid Eugen Grimm
David Eugen Grimm
AWAxel Wendt
Axel Wendt
To validate the accuracy and reliability of onboard sensors for object detection and localization in driver assistance, as well as autonomous driving applications under realistic conditions (indoors and outdoors), a novel tracking system is presented. This tracking system is developed to determine the position and orientation of a slow-moving vehicle (e.g. car during parking maneuvers), independent of the onboard sensors, during test maneuvers within a reference environment. One requirement is a 6 degree of freedom (DoF) pose with a position uncertainty below 5 mm (3σ), an orientation uncertainty below 0.3° (3σ) at a frequency higher than 20 Hz, and a latency smaller than 500 ms. To compare the results from the reference system with the vehicle’s onboard system, a synchronization via Precision Time Protocol (PTP) and a system interoperability to Robot Operating System (ROS) is implemented. The developed system combines motion capture cameras mounted in a 360° panorama view set-up on the vehicle with robotic total stations. A point cloud of the test site serves as a digital twin of the environment, in which the movement of the vehicle is simulated. Results have shown that the fused measurements of these sensors complement each other, so that the accuracy requirements for the 6 DoF pose can be met, while allowing a flexible installation in different environments.

2 June 2016 in Science
Verified
Journal Article
Closed access
DGDavid Eugen Grimm
David Eugen Grimm
But all living dogs have Asian roots

8 August 2025 in Preprints.org
Verified
Preprint
Open access
PDF file
AQAmna Qayyum
Amna Qayyum
JBJoël Bachmann
Joël Bachmann
DGDavid Eugen Grimm
David Eugen Grimm
Rapid advancements in surveying technology have necessitated the development of more accurate and efficient tools. Leica Geosystems AG, a leading provider of measurement and surveying solutions, has initiated a study to enhance the capabilities of its GNSS INS-based surveying systems. This research focuses on integrating the Leica GS18I GNSS receiver and the AP20 AutoPole with a Time of Flight (ToF) camera through sensor fusion. The primary objective is to leverage the unique strengths of each device to improve accuracy, efficiency, and usability in challenging surveying environments. Results indicate that the AP20-ToF integration maintains decimeter-level accuracy and precision. Conversely, the GS18I-ToF integration exhibits decreased accuracy and requires further optimization. The fused AP20 configuration demonstrates superior efficiency and ease of use in challenging conditions compared to the GS18I setup. This analysis confirms the efficacy of the fused AP20 system, with deviations within acceptable limits for most practical applications, while highlighting the need for further refinement of the GS18I configuration.

7 September 2026 in Smart Cities
Verified
Journal Article
Open access
PDF file
DHDaria Hollenstein
Daria Hollenstein
MAManuela Ammann
Manuela Ammann
DGDavid Eugen Grimm
David Eugen Grimm
Susanne BleischSusanne Bleisch
Susanne Bleisch
Surface macrotexture is of major interest for barrier-free routing, particularly for wheelchair travellers, because it relates to the functional properties of pavements, such as loss of energy through tyre-rolling resistance or vibrational discomfort. These functional properties are difficult to assess. The measurement and characterization of pavement macrotexture, therefore, is a promising approach to support safe route choice for wheelchair travellers and to provide comparative quality criteria for inclusive urban infrastructure management and planning. We use 3D point clouds from terrestrial laser scanning (TLS) and suggest a set of surface roughness parameters tailored to assess the accessibility of urban pavements at the micro-level. We explore the sensitivity of the parameters to point cloud resampling and apply them to a real-world dataset with eleven different pavements. In spite of value variation related to scanning distance and coverage, our results indicate that combining median-based versions of Average Roughness and Simulated Texture Depth together with parameters tailored to quantify the depth and proportion of joints and the roughness of the contact area facilitates the grouping and comparison of surfaces regarding barrier-free mobility. The results of this work will be integrated into a framework for accessibility analysis and barrier-free routing.