With the miniaturization and functionalization of electronic equipment, the problem of chip heat dissipation has become a serious challenge. In this article, a plasma reaction technology is applied to improve the heat dissipation performance between the thermal interface material (TIM) and the heat spreader. Oxygen plasma can not only improve the surface wettability of the heat spreader, but also form a thin layer of nickel oxide on the heat spreader surface. Nickel oxide can act as a layer of phonon transfer bridge between heat spreader and TIM to enhance the phonon transfer at the interface. The as obtained packaged module has a 42.50% decrease in thermal resistance compared to the original module. Moreover, molecular dynamics simulations were conducted to investigate the mechanism of nickel oxide layer promoting phonon interface conduction.
20 June 2024 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Copper-based conductive inks have been extensively researched due to their low sintering temperature and high anti-oxidation properties for various electrical devices. However, the unstable oxidation properties of copper (Cu) limit its practical application. Existing anti-oxidation methods adopted in copper sintering often reduce copper strength and reliability. Therefore, the study presents a novel copper composite ink comprising copper precursors, copper microparticles, organic protective agents, and antioxidants. The sintering process is simple, requiring only 20 minutes at 300°C in nitrogen without any additional pressure. As a result, sintered copper with an oxidation rate of only 3.21 wt% was successfully obtained using the mixed ink of copper particles and precursors. The porosity of the sintered copper is 10.69%, which is a 71.77% reduction compared to the copper sintered by using pure copper precursor ink, thanks to the synergistic effect. Furthermore, the study discusses and analyzes the lattice growth mechanism and synergy mechanism of copper particles and their precursors during copper sintering.
19 March 2025 in Physical Chemistry Chemical Physics
Flip chips have been widely used in microelectronic packaging to meet the requirements of high density and optimal performance; the thermal interface material (TIM) is the primary bottleneck for heat dissipation in flip-chip packages. Vertically aligned thermal pads offer higher thermal conductivity compared with thermal gels, yet their poor interface bonding strength makes their application challenging. In this study, a silane coupling agent (KH550) was applied to improve the bonding strength between the TIM and heat spreader (HS). The presence of the silane coupling agent intermediate layer enabled the TIM and HS to be connected via covalent bonds, greatly improving their bonding strength. The shear strength of the interface between the TIM and HS was increased by 610.7%, and the interface thermal resistance was decreased by 52.78%. Moreover, molecular dynamics simulation was conducted to investigate the interface bonding mechanism.
9 May 2025 in IEEE Transactions on Components, Packaging and Manufacturing Technology
As the demand for thermal management of large-size chips grows, indium is considered an ideal thermal interface material (TIM) due to its inherent high thermal conductivity and good ductility. For large-size flip chip packaging, how to enhance reliability, especially under temperature cycling, remains a challenge. With large-size flip chip packaging as its research object this study employed a method that combines finite element simulation and experiments to systematically analyze the creep behavior and morphological evolution of indium under temperature cycling. Based on this analysis, the fatigue life of indium was predicted using the strain-based Coffin-Manson model. To enhance the reliability of the indium layer under temperature cycling, a Design of Experiments (DOE) simulation scheme was used to analyze the influence of varying structural parameters on fatigue life. The results demonstrate that the accumulated plastic strain at the position close to the edge of the chip is the largest, aligning with the position of the crack observed in actual measurements. The fatigue life of the indium layer, as predicted by the Coffin-Manson model, is found to be basically consistent with the measured results. A signal-to-noise ratio (SNR) analysis indicates that the indium thickness has the greatest impact on the thermal fatigue life, while the adhesive thickness has the least impact on the thermal fatigue life. Compared with the original model, the fatigue life of the optimized packaging structure is increased by 135%.
24 February 2025 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Traditional packaging with bonded aluminum (Al) wires results to high parasitic inductance and reliability issues, therefore limiting the development of silicon carbide (SiC) power devices. Copper clip (Cu-clip) interconnection process have been proposed, which allows for better heat dissipation and thus enhances the power density of the device. While current research has primarily focused on its thermal performance and reliability, many issues remain unresolved. However, concentrated stress and electrical issue for multi-chip Cu-clip interconnects are still big challenges in the clip-bonded SiC MOSFET power device. Our work proposes an arch clip with unloading groove (Arch-G) structure that can effectively reduce the stress of Cu-clip devices, demonstrating a 39.1% reduction compared with conventional planar clip devices. Compared with wire-bonded devices, the Arch-G clip device boasts lower conduction losses and its parasitic inductance is reduced by 32.6%. Reliability via power cycling test of the Arch-G clip devices were also characterized experimentally. This work serves as a valuable reference for the design of high-performance Cu-clip power device.
The high thermal conductivity and good insulating properties of boron nitride (BN) make it a promising filler for high-performance polymer-based thermal management materials. An easy way to prepare BN-polymer composites is to directly mix BN particles with polymer matrix. However, a high concentration of fillers usually leads to a huge reduction of mechanical strength and optical transmission. Here, we propose a novel method to prepare polyethylene/boron nitride nanoplates (PE/BNNPs) composites through the combination of electrostatic self-assembly and hot pressing. Through this method, the thermal conductivity of the PE/BNNPs composites reach 0.47 W/mK, which gets a 14.6% improvement compared to pure polyethylene film. Thanks to the tight bonding of polyethylene with BNNPs, the tensile strength of the composite film reaches 1.82 MPa, an increase of 173.58% compared to that of pure polyethylene film (0.66 MPa). The fracture stress was also highly enhanced, with an increase of 148.44% compared to pure polyethylene film. Moreover, the addition of BNNPs in PE does not highly reduce its good transmittance, which is preferred for thermal management in devices like light-emitting diodes. This work gives an insight into the preparation strategy of transparent and flexible thermal management materials with high thermal conductivity.