Aleksandr I. Shikhov

Mr. Aleksandr I. Shikhov

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 February 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
VSVladimir Syasko
Vladimir Syasko
ASAleksandr I. Shikhov
Aleksandr I. Shikhov
About 60% of the territory of the Russian Federation is covered by permafrost. Additionally, a large share of the country’s mineral and hydrocarbon deposits are located in the Arctic. Climate change that has been happening over the past few decades has had a serious impact on the conditions in which permafrost soils are found. Changes in temperatures in permafrost regions, along with the human impact from mining and processing, have led to an increase in accidents caused by the degradation of permafrost foundations. In this situation, timely detection of the degradation of permafrost foundations plays a pivotal role in ensuring the safe operation of buildings and structures. This article contains a theoretical review and describes the results of an experimental study of whether it is possible to use acoustic testing in solving problems associated with monitoring the state of permafrost foundations. In the course of the study, the relationships between the acoustic characteristics and the deformation and strength characteristics of permafrost soils were analysed. The results of the study made it possible to draw a preliminary conclusion that acoustic testing can be used to solve problems associated with condition monitoring of permafrost foundations.

1 May 2024 in Russian Journal of Nondestructive Testing
Verified
Journal Article
Closed access
PDF file
LML. Yu. Mogilner
L. Yu. Mogilner
VSVladimir Syasko
Vladimir Syasko
ASAleksandr I. Shikhov
Aleksandr I. Shikhov
In the introduction to the article we mention four factors that are most important for ensuring the accuracy of characterizing defects during ultrasonic inspection, viz., parameters of artificial reflectors in samples, compliance of the acoustic properties of the material of tuning samples and tested products, transient characteristics of electroacoustic paths, and methodological features of measurements. The present article is devoted to the analysis of the first and partly fourth of listed factors. The review of reflectors, the use of which is regulated in various standards, is carried out. Advantages and disadvantages of flat-bottomed holes, segmental and corner reflectors (“notches”), lateral (SDH) and vertical cylindrical holes, and grooves are noted. Taking into account the specific features of ultrasonic wave scattering, it is noted that artificial “reflectors” such as “grooves” and SDHs are used to adjust the parameters of modern diffraction testing methods. It is recommended to expand the use of grooves, SDHs, and vertical drilling when revising the standards governing the use of conventional echo methods. The estimation of accuracy of measurement of defects parameters, first of all, the crack tip coordinates, with application of modern digital methods of information processing during ultrasonic testing is given. It is indicated that to increase the measurement accuracy and to determine the position and orientation of cracks in welds, it is necessary to create a database of digital twins of samples with artificial reflectors and products with real defects. A general scheme of executing the quality control is given that takes into account the use of standards (measures), digital models of artificial reflectors, and digital twins of the testing process to ensure the necessary detectability of defects and reliability of manual, automated, and, potentially, automatic testing.

1 February 2021 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
APA I Potapov
A I Potapov
ASAleksandr I. Shikhov
Aleksandr I. Shikhov
EDE N Dunaeva
E N Dunaeva
A great part of the territory of the Russian Federation is located in the zone of permafrost soils. Safe operation management of buildings and structures, in permafrost conditions, requires geotechnical monitoring of subgrade soils. The increase in air temperature recorded during numerous monitoring leads to the degradation of permafrost soils. Therefore, the problem of conducting geotechnical monitoring becomes more urgent than ever. This paper analyzes the existing methods and systems for geotechnical monitoring of permafrost soils. The authors reveal the drawbacks of the applied methods and the reasons that do not allow assessing the state of frozen soils with sufficient accuracy. In order to solve these problems, it is proposed to use an active acoustic method of non-destructive testing and create a system that combines an engineering-geological method determining the deformation properties of frozen soils and active acoustic method.

4 June 2021 in E3S Web of Conferences
Verified
Conference Paper
Open access
PDF file
VSVladimir Syasko
Vladimir Syasko
ASAleksandr I. Shikhov
Aleksandr I. Shikhov
Much of the territory of the Russian Federation is located in the permafrost soil area. The developed hydrocarbon deposits make a significant contribution to the budget of the Russian Federation. Therefore, ensuring trouble-free operation of engineering structures and these fields is the most crucial task. Frozen soil deformation leads to violations in the operation of structures, which entail economic harm and significant environmental problems. This article provides a brief overview of the leading causes of deformations of engineering structures built on permafrost soils. The methods currently used to stabilize the frozen soil deformation are considered, and the directions for solving this problem are proposed.

1 March 2025 in Russian Journal of Nondestructive Testing
Verified
Journal Article
Closed access
PDF file
ASAleksandr I. Shikhov
Aleksandr I. Shikhov
Kirill GogolinskyKirill Gogolinsky
Kirill Gogolinsky
AZA. S. Zubarev
A. S. Zubarev
YSYa. G. Smorodinsky
Ya. G. Smorodinsky
DKDarya V. Kopytina
Darya V. Kopytina
AVAnna Vinogradova
Anna Vinogradova
Establishing requirements for acoustic measurements and calibration blocks and monitoring their implementation during production and certification is an important task. In this paper, the parameters affecting the propagation velocity of elastic waves in steel are considered, and their contribution to the total uncertainty of measuring the propagation velocity of a longitudinal wave is determined. Based on the data obtained, an analysis of the standards devoted to ultrasonic testing methods was carried out in terms of the requirements for calibration blocks. The conducted research allowed us to establish that the requirements imposed by the current standards do not sufficiently take into account a number of factors that may affect the characteristics of ultrasound measures and reference samples. Standard samples made without taking these factors into account are unlikely to adequately assess the metrological characteristics of ultrasound equipment.

20 August 2025 in Metrology
Verified
Journal Article
Open access
PDF file
ASAleksandr I. Shikhov
Aleksandr I. Shikhov
Kirill GogolinskyKirill Gogolinsky
Kirill Gogolinsky
DKDarya V. Kopytina
Darya V. Kopytina
AVAnna Vinogradova
Anna Vinogradova
AZAleksei Zubarev
Aleksei Zubarev
This article investigates the acoustic properties of artificial discontinuities in reference specimens for the ultrasonic testing of welded joints in polyethylene pipes. An analysis is conducted on the reflectivity of various materials (air, sand, heat-resistant silicate-based sealant, and aluminum foil) and their correspondence to real defects occurring in weld seams. A theoretical analysis of reflection coefficients is performed, along with laboratory studies using digital radiography and ultrasonic testing. The results demonstrate that heat-resistant silicate sealant is the most suitable material for simulating defects, as its acoustic properties closely match those of real inclusions, and its geometric parameters remain stable during the welding process. The use of such specimens enhances the reliability of ultrasonic testing and reduces the likelihood of errors in defect classification.