Jan Skocilas

Prof. Jan Skocilas

orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2013 in Manufacturing Technology
Verified
Journal Article
Open access
PDF file
BSBlanka Skočilasová
Blanka Skočilasová
JSJan Skocilas
Jan Skocilas
The paper deals with the mathematic modeling of the liquid turbulent flow in the pipe with circular cross-section. The aim is to compare two methods of solution for various geometries and Reynolds numbers. One of the methods is simulation of t...

1 January 2013 in Latin American Journal of Solids and Structures
Verified
Journal Article
Open access
PDF file
JSJan Skocilas
Jan Skocilas
BSBlanka Skočilasová
Blanka Skočilasová
JSJosef Soukup
Josef Soukup
The article deals with systematic analysis of the transient vibration of rectangular viscoelastic orthotropic thin 2D plate. The analysis is focused on specific deformation models of plate and for specific linear models of rheological properties. The viscoelastic isotropic and anisotropic (orthotropic) materials were investigated. The plate is loaded by general transient impulse. The time and coordinate dependencies of the fundamental quantities - displacements, rotations, stress and deformations in arbitrary points of plate under transient vibration, e. g. the analysis of stress and deformation waves in plates were investigated. The selected models are defined by constitutive equations for stress and deformation dependence. The isotropic and orthotropic model is considered. The analysis results depend on quality of the determined mechanical properties of the materials. The standard methods commonly used are time-consuming and not accurate enough. The new methodology of determining the material parameters directly from investigated plate is proposed and proven.

27 December 2014 in Procedia Engineering
Verified
Journal Article
Open access
PDF file
NNN.F. Nangolo
N.F. Nangolo
JSJ. Soukup
J. Soukup
LRL. Rychlíková
L. Rychlíková
JSJan Skocilas
Jan Skocilas
In this paper the vertical vibration response of a 9 degrees-of-freedom (DOF) 4-axle freight wagon, modeled as a multi-body system is investigated. The Lagrange's equation is used to obtain the equations of motion, and the corresponding system matrices are then assembled. A combined modal analysis and numerical integration of the convolution integral is adopted, which is achieved by programming a MATLAB script. Modal analysis is used to uncouple the differential equations and thereafter, the convolution integrals are numerically integrated using piecewise constants as interpolating functions. The Complex-Exponential Method (CEM) is then used to extract damping ratio, mode shapes and the system's natural frequencies from test data, this information is then used to compute the numerical solution. The developed models are then validated with measured data.

31 January 2022 in Polymers
Verified
Journal Article
Open access
PDF file
HCHynek Chlup
Hynek Chlup
JSJan Skocilas
Jan Skocilas
JŠJaromír Štancl
Jaromír Štancl
Milan HouśkaMilan Houśka
Milan Houśka
RZRudolf Zitny
Rudolf Zitny
This article describes 1D extension tests on bovine collagen samples (8% collagen in water). At such a high collagen concentration, the mechanical properties of semi-solid samples can be approximated by hyperelastic models (two-parametric HGO and Misof models were used), or simply by Hooke’s law and the modulus of elasticity E. The experiments confirm a significant increase in the E-modulus of the samples irradiated with high-energy electrons. The modulus E ~ 9 kPa of non-irradiated samples increases monotonically up to E ~ 250 kPa for samples absorbing an e-beam dose of ~3300 Gy. This amplification is attributed to the formation of cross-links by irradiation. However, E-modulus can be increased not only by irradiation but also by exposure to a high strain rate. For example, soft isotropic collagen extruded through a 200 mm long capillary increases the modulus of elasticity from 9 kPa to 30 kPa, and the increase is almost isotropic. This stiffening occurs when the corrugated collagen fibers are straightened and are aligned in the flow direction. It seems that the permanent structural changes caused by extrusion mitigate the effects of the ex post applied irradiation. Irradiation of extruded samples by 3300 Gy increases the modulus of E-elasticity only three times (from 30 kPa to approximately 90 kPa). Extruded and ex post irradiated samples show slight anisotropy (the stiffness in the longitudinal direction is on an average greater than the transverse stiffness).

1 January 2014 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
BSBlanka Skočilasová
Blanka Skočilasová
JSJan Skocilas
Jan Skocilas
The article deals with method applied to the verification of the turbulence models. The turbulence models were used in the simulation of the Newtonian fluid turbulent flow in the circular tube. The principle of the method is in the comparison of the pressure drop obtained by the simulation and the analytic solution. The parameters of the fluid flow were varied with the specified Reynolds number range. The pressure drop of inserted element in the pipe is evaluated.

7 May 2016 in Journal of Texture Studies
Verified
Journal Article
Closed access
PDF file
JSJan Skocilas
Jan Skocilas
RŽRudolf Žitný
Rudolf Žitný
JŠJaromír Štancl
Jaromír Štancl
MDMartin Dostál
Martin Dostál
ALAleš Landfeld
Aleš Landfeld
MHMilan Houška
Milan Houška