Tomasz Chaciński

Mr. Tomasz Chaciński

Koszalin University of Technology, Faculty of Mechanical Engineering
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 December 2021 in Micromachines
Verified
Journal Article
Open access
PDF file
BZBartosz Zieliński
Bartosz Zieliński
TCTomasz Chaciński
Tomasz Chaciński
Danil PimenovDanil Pimenov
Danil Pimenov
KNKrzysztof Nadolny
Krzysztof Nadolny
In the food industry, there are many varieties of technical blades with different contours as well as different cutting edge geometries. The evaluation of the ability of technical blades to separate (cut) animal tissues is not a simple task and is usually based on the evaluation of the cutting effects in a technological process. This paper presents a methodology for evaluating the cutting force of technical blades used in food processing. A specially made test stand with numerical control was used in the study. Its application enabled a comparison of cutting force values for four different cutting edge geometries of planar knives used in the skinning operation of flat fishes. A unique feature of the conducted research was the use of a relatively high cutting speed value of vf = 214 mm/s, which corresponded to the real conditions of this process carried out in the industry. Obtained test results allow unambiguously choosing the most advantageous variant of knife geometry from among four different variants used for the tests. The results showed a clear relationship between the cutting force value and the value of the tip angle of the blades tested: for blades with the lowest tip angle, the lowest cutting force values were obtained.

7 November 2022 in Materials
Verified
Journal Article
Open access
PDF file
BZBartosz Zieliński
Bartosz Zieliński
KNKrzysztof Nadolny
Krzysztof Nadolny
WZWojciech Zawadka
Wojciech Zawadka
TCTomasz Chaciński
Tomasz Chaciński
WSWojciech Stachurski
Wojciech Stachurski
Gilmar Ferreira BatalhaGilmar Ferreira Batalha
Gilmar Ferreira Batalha
This work presents the results of an experimental study of the sharpening of planar technical blades used in the fish processing industry. Sharpening was carried out in the grinding process using several environmentally friendly methods of cooling and lubricating the machining zone (MQL method, CAG nozzle, hybrid method that is a combination of MQL and CAG methods, as well as WET flooding method as reference). The purpose of the research was to determine the possibility of reducing the negative environmental impact of the sharpening process of technical blades by minimizing the expenditure of coolant. The application of the MQL method and the hybrid MQL + CAG method provided a very good realization of the lubricating function so that the share of friction of dulled cutting vertices against the workpiece surface is reduced, which manifests itself in the reduction of the grinding force and the correlated grinding power. In the case of grinding under cooled compressed air delivery conditions, the average cutting force was as much as 91.6% higher (F = 22.63 N) compared to the result obtained for the most favorable flooding method, demonstrating the insufficient quality of the blade shaped under such conditions. A comprehensive comparison of test results on grinding power gain, cutting force and surface texture suggests that the most favorable sharpening results were obtained using the environmentally friendly MQL method of cooling and lubricating the grinding zone.

11 November 2022 in Materials
Verified
Journal Article
Open access
PDF file
BZBartosz Zieliński
Bartosz Zieliński
KNKrzysztof Nadolny
Krzysztof Nadolny
WZWojciech Zawadka
Wojciech Zawadka
TCTomasz Chaciński
Tomasz Chaciński
WSWojciech Stachurski
Wojciech Stachurski
Gilmar Ferreira BatalhaGilmar Ferreira Batalha
Gilmar Ferreira Batalha
The most widely used method for shaping technical blades is grinding with abrasive tools made of cubic boron nitride (cBN) grains and vitrified bond. The goal of this work was to determine the effect of grinding wheel grain size (cBN grain number according to FEPA standards: B126, B181 and B251), kinematics (grinding with the circumference, face and conical surface of the wheel) and feed rate (vf = 100; 150; 200 mm/min) on the effects of the grinding process evaluated by the cutting force of the blade after machining F, blade surface texture parameters (Sa, St, Smvr, Str, Sdq, Sdr and Sbi) as well as blade surface morphology. An analysis of output quantities showed that grinding wheels made of B181 cBN grains are most favorable for shaping planar technical blades of X39Cr13 steel in the grinding process.

3 February 2023 in Applied Sciences
Verified
Journal Article
Open access
PDF file
TCTomasz Chaciński
Tomasz Chaciński
BZBartosz Zieliński
Bartosz Zieliński
KNKrzysztof Nadolny
Krzysztof Nadolny
Considering the technological processes taking place in fish processing enterprises (skinning), it is possible to specify various factors affecting the tool life and process efficiency. The paper presents the methodology of the study and the results and analysis of the collected data on the effect of the cutting speed of the technical blade used in the fish skinning process on the forces occurring in the cutting process. A special test stand was used in the study, which allowed obtaining repeatable results at a wide range of cutting speed values in the cutting process (70–400 mm/s). The study also determined the values of work W and power P, as well as the ej index (unit energy intensity index), which helped to select the most favorable blade feed rate parameter. The results indicated the most favorable cutting speed parameter and showed a clear relationship between the feed rate and the force and energy expenditure; as the cutting speed increases, an upward trend in force and energy expenditure was noted.

14 March 2023 in Journal of Mechanical and Energy Engineering
Verified
Journal Article
Open access
PDF file
TLTomasz Lewiński
Tomasz Lewiński
KKKrzysztof Kukiełka
Krzysztof Kukiełka
TCTomasz Chaciński
Tomasz Chaciński
PJPiotr Jaskólski
Piotr Jaskólski
This paper investigates the effect of additive manufacturing parameters on the manufacturing quality of selected gear mechanism components. Three input variables, and two output variables were determined. The result was the determination of the most optimal combination of key parameters and the determination of regression equations. The concept of manufacturing objects of a very complex shape, by any person, under various conditions through the use of a low-cost device became the basis for this thesis topic. Curing time, layer thickness, and lift speed are among the basic parameters, with a large range of manipulation. A hypothesis was formulated that these three parameters are crucial to produce a part with the smallest possible deviations from the computer model. A handheld scanner was used to scan the samples and compare them with the CAD model. Based on the study, optimal parameters for layer thickness, curing time and lift speed were proposed.

2 April 2023 in Applied Sciences
Verified
Journal Article
Open access
PDF file
PJPiotr Grzegorz Jaskólski
Piotr Grzegorz Jaskólski
TCTomasz Chaciński
Tomasz Chaciński
WZWojciech Zawadka
Wojciech Zawadka
KNKrzysztof Nadolny
Krzysztof Nadolny
The use of CNC equipment that integrates several machining operations allows the elimination of downtime resulting from setup changeovers and the clamping of workpieces in several different machine tools. More and more CNC machines and tools that allow the integration of several machining operations are appearing on the market, but there are only a few examples of these and many solutions that allow such integration for more complex operations are still missing. The aforementioned factors motivated the research work described in this paper. The purpose of the present study was to develop an innovative grinding head with different functional features for use in the process of shaped surfaces face grinding, the use of which will enable complete abrasive machining in a single mounting. The conducted tests of the grinding process showed a reduction in the values of the roughness parameters Sa (5.30, 1.12, 0.63 μm), St (31.8, 14.4, 6.72 μm), Sq (6.39, 1.46, 0.81 μm) and Spk (6.16, 0.77, 0.33 μm) and an increase in the value of the parameter Sds (393, 563, 1203 pks/mm2) on the surface after machining in two stages, first for rough grinding and then for finishing relative to the surface after the shaped milling process.