Additive manufacturing from metal powders using selective laser melting technology is gaining increasing interest in various industries. The purpose of this study was to determine the effect of changes in process parameter values on the relative density, microstructure and mechanical properties of Ti-6Al-4V and Ti-6Al-7Nb alloy samples. The experiment was conducted in response to a noticeable gap in the research on the manufacturability of the Ti-6Al-7Nb alloy in SLM technology. This topic is significant given the growing interest in this alloy for biomedical applications. The results of this study indicate that by properly selecting the volumetric energy density (VED), the relative density of the material produced and the surface roughness of the components can be effectively influenced. Microstructural analyses revealed similar patterns in both alloys manufactured under similar conditions, characterized by columnar β phase grains with needle-like α’ phases. Increasing the VED increased the tensile strength of the fabricated Ti-6Al-4V alloy components, while the opposite effect was observed for components fabricated from Ti-6Al-7Nb alloy. At the same time, Ti-6Al-7Nb alloy parts featured higher elongation values, which is desirable from the perspective of biomedical applications.
Despite extensive knowledge of the cutting methods described, no universal method has been developed so far for evaluating the technological quality of elements shaped by different cutting processes. The aim of the research described in this article was to fill this gap and to propose the author’s methodology for the assessment of the technological quality of the surface of X5CRNI18-10 steel shaped as a result of laser cutting and abrasive water jet cutting. A synthetic index of technological quality assessment of the surface after cutting CTQ (cutting technological quality) was proposed. Three groups of factors were taken into account in the assessment of technological quality of the surface after cutting: selected surface texture parameters (arithmetic mean deviation of the surface Sa and total height of the surface St), results of measurements of dimensional accuracy of cut elements (length deviation LD and width deviation WD) as well as indicators of surface morphology estimated on the basis of microscopic images of the surface after cutting (deformation intensity DI and identification of cutting zones ICZ). On the basis of CTQ values determined, the cutting results of both cutting methods were compared. The analyses presented in this paper proved that the CTQ index can be effectively used to compare the results of a cutting process conducted using different methods and under different conditions. The developed CTQ index is a universal valuation tool, allowing for quantitative evaluation of features related to the technological quality of cutting process results.
This article discusses a comparative analysis of the wear and quality of planer knife blades used in wood planers. The novelty in this work is the use of a simple coordinate measuring machine with a vision system to assess the wear of the cutting edges of planer knives. The primary objective of the research described in this paper was to verify whether the wear of the cutting edge of planer knives can be measured quickly and accurately using an optical coordinate measuring machine with a vision system. To date, contact profilometry methods have been used for this purpose, which require a specialist apparatus and qualified measuring equipment operators and are expensive and time-consuming. The research presented in this work was conducted on twelve planer knives. The condition and wear of the working surfaces of the tested knives were assessed using an optical digital microscope. The wear of the cutting edge of the knives was measured using two methods: the contact profilometry method and an optical coordinate measuring machine equipped with a vision system. The edge profiles and their parameters obtained by the optical method were compared to the results of measurements with a stylus profilometer. Based on the research and analyses conducted, it was found that the optical method used in this research significantly shortens the time of measuring the wear of the cutting edges of planer knives. In addition, this method has a wider measurement range, and the obtained measurement results are characterized by lower measurement uncertainty.
This work presents the results of an experimental study of the sharpening of planar technical blades used in the fish processing industry. Sharpening was carried out in the grinding process using several environmentally friendly methods of cooling and lubricating the machining zone (MQL method, CAG nozzle, hybrid method that is a combination of MQL and CAG methods, as well as WET flooding method as reference). The purpose of the research was to determine the possibility of reducing the negative environmental impact of the sharpening process of technical blades by minimizing the expenditure of coolant. The application of the MQL method and the hybrid MQL + CAG method provided a very good realization of the lubricating function so that the share of friction of dulled cutting vertices against the workpiece surface is reduced, which manifests itself in the reduction of the grinding force and the correlated grinding power. In the case of grinding under cooled compressed air delivery conditions, the average cutting force was as much as 91.6% higher (F = 22.63 N) compared to the result obtained for the most favorable flooding method, demonstrating the insufficient quality of the blade shaped under such conditions. A comprehensive comparison of test results on grinding power gain, cutting force and surface texture suggests that the most favorable sharpening results were obtained using the environmentally friendly MQL method of cooling and lubricating the grinding zone.
This article presents the results of experimental studies of the centrifugal disc finishing (CDF) process of 304 steel elements with the use of an active workpieces holder, that allows workpieces for additional rotational and oscillation movements. The main aim of the research was to evaluate the mechanism of formation of the surface texture and to assess the intensity and effectiveness of the machining process. It is shown that additional movements of the workpiece significantly affect the formation of the machining traces generated by the elementary phenomena of micro-cutting, scratching, grooving, etc. As a result, these combined and complex interactions lead to the formation of the surface topography of the workpieces. Based on the research results, it can be concluded that the use of an active workpiece holder in the CDF process allows changes in the intensity of the machining process. Moreover, the active holder allows modification of the surface smoothing process. The intensity of the treatment process depends primarily on the location of the workpiece holder in the appropriate energy area of the work charge. On the other hand, the efficiency of the workpiece surface smoothing depends on the parameters of the oscillation and rotational movements of the workpiece mounted in the active holder. The presented research results show that the use of an active holder, enabling rotation and oscillation of the workpiece, may lead to a more effective use of smoothing processes in CDF machines. The analysis of the results shows that the values of the Sdr and Sa parameters are more strongly dependent on the vibration frequency and increase with its increasing frequency. This is undoubtedly the result of the concentration of smoothing marks on the smoothed surface. However, with regard to the rotational speed of the object, this relationship is non-monotonic, and its greatest influence occurs at its intermediate values. It follows that this activity does not have a significant impact on the generation of the number of smoothing marks and the degree of their concentration. The research methodology proposed in the work allows the initial determination of the dependence of the results of the CDF process on the machining parameters, including the parameters of the active holder. This methodology can also be used for machining materials other than AISI 304 steel.
The use of CNC equipment that integrates several machining operations eliminates downtime due to changes in setup and clamping of workpieces in more than one machining device. A review of CNC equipment and tools known from the literature and from manufacturers’ offerings indicates that new technical solutions are being developed to integrate two or more technological operations. However, these examples have numerous limitations and are mostly not suitable for machining surfaces with complex shapes. An example of such solutions is the use of a dual-tool grinding head, which integrates the process of rough grinding with a ceramic grinding wheel and finish grinding with a flexible grinding wheel. Unfortunately, it has the disadvantage of being limited by the angular shape of the ceramic grinding wheel, making it unable to adapt to the complex geometries of the shaped surfaces being ground. The need to overcome this limitation became the motivation for the research work described in this article. By means of experimental research, it was verified what effect the radial outline on the periphery of a ceramic grinding wheel realized by rough grinding would have on the surface roughness parameters obtained in the process of grinding shaped surfaces. For this purpose, grinding processes using a ceramic wheel with a conical and radial outline were compared. The result of the study was a summary of the surface roughness parameters Sa, St, Sq, Spk, Str, and Sds obtained after two-stage machining (rough and finish grinding). The obtained analysis results showed that changing the axial outline of the ceramic grinding wheel makes it possible to significantly expand the range of applications of the dual-tool head without negatively affecting the quality of the machined surface. Thus, such an improvement will make it possible to increase the applicability of the head by grinding shaped surfaces with a radial profile of curvature.