Qiuhong Li

Dr. Qiuhong Li


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2021 in Aerospace Science and Technology
Verified
Journal Article
Closed access
SPShuwei Pang
Shuwei Pang
QLQiuhong Li
Qiuhong Li
BNBo Ni
Bo Ni

8 August 2022 in Aerospace Science and Technology
Verified
Journal Article
Closed access
ZGZiyu Gu
Ziyu Gu
SPShuwei Pang
Shuwei Pang
YLYuchen Li
Yuchen Li
QLQiuhong Li
Qiuhong Li
YZYongliang Zhang
Yongliang Zhang

18 March 2019 in IEEE Access
Verified
Journal Article
Open access
SPShuwei Pang
Shuwei Pang
QLQiuhong Li
Qiuhong Li
HFHailong Feng
Hailong Feng
HZHaibo Zhang
Haibo Zhang
In the field of aero-engine control, it is valuable to build highly accurate component level models to meet the requirement of controller validation and model-based control. The accuracy of current performance map generation method is limited by the test data that always cannot cover the full envelope. The scaling-based performance map correction methods only focus on the adjustment of the steady state performance. Therefore, a performance map segmentation based joint steady state and transient performance adaptation technique is proposed. Both the idle point and the design point are taken as precision references to scale the performance maps with large deviation. A scaling factor domain determination method is provided based on the characters of the speed lines. The performance map is first optimized with the steady state model based on the steady state test data, and further optimized with the transient model based on the transient test data. Both steady state and transient performance adaptations are achieved by adjusting the performance maps. The proposed method was applied to a turbofan engine model. For continuous acceleration case, the average error are less than 1% at steady state points and less than 2% during transient operation. For large magnitude acceleration and rapid deceleration cases, the maximum errors for parameters around the idle point decrease by about one times (from 8.3% to 4.1%) and three and a half times (from 28% to 8%) respectively by comparing with the model without transient performance adaptation. Thus, the effectiveness of the proposed method is demonstrated.

9 February 2022 in Energies
Verified
Journal Article
Open access
PDF file
ZGZiyu Gu
Ziyu Gu
SPShuwei Pang
Shuwei Pang
WZWenxiang Zhou
Wenxiang Zhou
YLYuchen Li
Yuchen Li
QLQiuhong Li
Qiuhong Li
The linear parameter-varying (LPV) model is widely used in aero engine control system design. The conventional local modeling method is inaccurate and inefficient in the full flying envelope. Hence, a novel online data-driven LPV modeling method based on the online sequential extreme learning machine (OS-ELM) with an additional multiplying layer (MLOS-ELM) was proposed. An extra multiplying layer was inserted between the hidden layer and the output layer, where the hidden layer outputs were multiplied by the input variables and state variables of the LPV model. Additionally, the input layer was set to the LPV model’s scheduling parameter. With the multiplying layer added, the state space equation matrices of the LPV model could be easily calculated using online gathered data. Simulation results showed that the outputs of the MLOS-ELM matched that of the component level model of a turbo-shaft engine precisely. The maximum approximation error was less than 0.18%. The predictive outputs of the proposed online data-driven LPV model after five samples also matched that of the component level model well, and the maximum predictive error within a large flight envelope was less than 1.1% with measurement noise considered. Thus, the efficiency and accuracy of the proposed method were validated.

17 January 2025 in Aerospace
Verified
Journal Article
Open access
PDF file
HCHongyi Chen
Hongyi Chen
QLQiuhong Li
Qiuhong Li
叶Y叶志锋 Zhifeng Ye
叶志锋 Zhifeng Ye
SPShuwei Pang
Shuwei Pang
Servo systems are important actuators of aeroengines. The repetitive, reciprocating motion of the servo system leads to significant changes in its time delay and gain characteristics, and degradation increases the uncertainty of these changes. These characteristic variations may have an adverse effect on the dynamic performance of the aeroengine. Therefore, a neural network-based parameter estimation and a multi-loop neural network-based predictive control (ML-NNPC) method for aeroengine inlet guide vane (IGV) servo systems (SVS) were proposed. In this study, the time delay estimation of the servo system was treated as a classification problem, and an SE (squeeze-and-excitation)-GRU (gated recurrent unit) network was proposed to estimate the time delay by using the selected dynamic data of the servo system. The estimated delay was embedded into an online sequential extreme learning machine, and a nonlinear model predictive controller was designed to obtain an optimal control sequence. The compensation control loop was designed to reduce the impact of the model and delay mismatch problems of the control system. The proposed method was applied to the IGV SVS control of a turboshaft engine. The simulation results demonstrate that the time delay is estimated accurately and compensated effectively. Compared to the existing PI and PI with Smith predictor methods, the ML-NNPC method achieves better control performance in the control of both the SVS and the engine rotor speed system. The stability and robustness of the ML-NNPC also show superiority. The results verify the effectiveness of the proposed time delay estimation method and the ML-NNPC method.

25 May 2022 in Energies
Verified
Journal Article
Open access
PDF file
HCHongyi Chen
Hongyi Chen
QLQiuhong Li
Qiuhong Li
SPShuwei Pang
Shuwei Pang
WZWenxiang Zhou
Wenxiang Zhou
State space models (SSMs) are important for multi-variable performance analysis and controller design of aero-engines. In order to solve the problems of the traditional state space modeling methods that rely on component-level models (CLMs) and cannot be carried out in real time, an aero-engine state space modeling method based on adaptive forgetting factor online sequential extreme learning machine (AFOS-ELM) is proposed in this paper. The structure of the extreme learning machine (ELM) is determined according to the form of the state space model, and the inverse-free ELM algorithm is used to automatically select the appropriate number of hidden nodes to improve the efficiency of offline initialization. The focus of the ELM on current operation performance is enhanced by the adaptive renewed forgetting factor, which reduces the impact of aero-engine history and deviated data on the current output and improves the accuracy of the model. Then, according to the analytical equation of the ELM model, the state space model of an aero-engine at each sampling time is obtained by using the partial derivative method. The simulation results based on engine test data show that the real-time performance and accuracy of the state space model established online in this paper can meet the needs of aero-engine control system requirement.