A two-dimensional (2-D) camera system with a real-time image processing-based safety technology is a cost-effective alternative that needs optimization of the cell layout, the number of cameras, and the camera’s locations and orientations. A design optimization study was performed using the multi-criteria linear fractional programming method and considering the number of cameras, the resolution, as well as camera positions and orientations. A table-top experimental setup was designed and built to test the effectiveness of the optimized design using two cameras. The designs at optimal and nonoptimal parameters were compared using a deep learning algorithm, ResNet-152. To eliminate blind spots, a simple but novel 2-D image merging technique was proposed as an alternative to commonly employed stereo imaging methods. Verification experiments were conducted by using two camera resolutions with two graphic processors under varying illuminance. It was validated that high-speed entrances to the safety system were detected reliably and with a 0.1 s response time. Moreover, the system was proven to work effectively at a minimum illuminance of 120 lux, while commercial systems cannot be operated under 400 lux. After determining the most appropriate 2-D camera type, positions, and angles within the international standards, the most cost-effective solution set with a performance-to-price ratio up to 15 times higher than high-cost 3-D camera systems was proposed and validated.
2 September 2021 in Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
Günümüzde robotların sanayi ve günlük yaşamda kullanım alanları artmakta ve bununla birlikte uygulamaların robotlar tarafından yerine getirilmesi için farklı robot tasarımları geliştirilmektedir. Paralel robotlar, kapalı zincir kinematik yapısından dolayı kısıtlanmış çalışma uzayına sahiptir. Bunun yanı sıra bu kinematik yapı robota yüksek konum hassasiyeti ve rijitlik kazandırmaktadır. Rehabilitasyon robotlarında; rijit yapı ve hassas pozisyonlama en önemli unsurlardır bu nedenle paralel robotlar rehabilitasyon uygulamalarına uygundur. Bununla birlikte, paralel robotların sınırlı çalışma uzayı eklem hareket açıklığında kısıt oluşturmaktadır. Bu çalışmada; Stewart Platform yapısına, 7’inci lineer aktüatör ve buna bağlı bir mekanizma ilave edilerek, çalışma uzayı genişletilerek daha fazla alt uzuv eklemine rehabilitasyon yapılmasını sağlayan yeni bir robot tasarlanmıştır. Mekanik tasarım, elektronik donanım, Newton-Raphson sayısal yöntemiyle ileri kinematik ve vektörel ters kinematik hesaplamalarıyla oluşturulan matematiksel alt yapısı ve PID pozisyon kontrolü birleştirilerek rehabilitasyon robotu tasarlanmıştır. İnsan bacağı üzerinde yapılan deneylerle robotun, ayak bileği ve diz eklem hareket açıklıklarını gerçekleştirebilme ve pozisyonlama sonuçları değerlendirilmiş ve literatürle karşılaştırılmıştır. Deneysel ölçümlere göre yörünge takibinde zaman gecikmesi 0,5 saniyenin altında ve azami açı sapması 1,2° elde edilmiştir.
1 February 2022 in Journal of Engineering and Science in Medical Diagnostics and Therapy
Nowadays, gimbal systems have been a very critical role to obtain some important information related to live images photos and target detection in unmanned aerial vehicles. The most basic performance criterion of gimbal systems depends on its stabilization in which the desired reference tracking must be accomplished by designing complex controller structure. For this purpose, a discrete controller design is presented to provide reduced cost, high-performance, 3-axis gimbal systems in real-time operation. Firstly, the mathematical model of the system was obtained and 3D – computer aided design was made in order to calculate the system parameters like inertia, damping factor, etc. After that forward and inverse kinematic equations for the gimbal system were obtained in order to calculate the reference degree in each axis. The discrete controller was derived from energy-based computed torque proportional controller which was based on the Lyapunov Stability Theorem in discrete notation. The reference tracking results at 10 milliseconds sampling time are as follows; 0 overshoot for 3 axes with lack of steady-state errors, and the time constants are 0.1575, 0.1610, and 0.27 second which are acceptable for roll, pitch, and yaw axes, respectively. In addition, the discrete-time performance of the proposed controller was compared with a PID controller designed in continuous time, and it was shown that the continuous-time design did not work efficiently as well as discrete time one.
About Me
Associate Professor, Faculty Member in Mechatronics Engineering Department of Yildiz Technical University
Associate Professor, Faculty Member in Mechatronics Engineering Department of Yildiz Technical University